Processing equipment

Overview： This product is a new type of mold copper plate surface cladding detection equipment. The equipment adopts a high-precision and high-sensitivity laser ranging sensor, which scans the copper plate of the mould by scanning a laser line with a fixed width, and returns the measurement data in real time. After modeling and analyzing the data, the upper computer gives the wear data of the mold copper plate, as well as the data of surface cracks and surface roughness. The host computer software intuitively reflects the surface profile of the detected mold and cladding thickness deviation and other data to the user in the form of data sheet, data curves and mold 3D model diagrams, providing a true and reliable theory for on-site operators to maintain the mold. The mold surface cladding detection equipment is a high-precision instrument, which includes high-precision laser ranging sensors, two digital servomotors, encoders, horizontal sliding screws, vertical sliding screws, and calibration consoles, controllers and other components. The equipment has many advantages such as high accuracy, strong stability, convenient installation and strong observability. It is suitable for mold surface cladding detection, surface flatness analysis, surface flaw detection, taper measurement, etc. It is also suitable for round billets, square billets, slabs, special-shaped billets, etc., widely used and powerful. The composition of the system： 1. The mold surface cladding detection equipment is equipped with: data processing and display unit, horizontal motion mechanical power output unit, vertical mechanical power output unit, instrument motion control unit, laser measurement sensor, and instrument bracket. 2. Data processing and display unit: used for data acquisition and storage, system equipment control, parameter configuration, height display of the descent, start and stop control, etc. 3. Horizontal motion mechanical power output unit: the digital servo motor in the horizontal direction controls the sensor to move in the horizontal direction, so that the sensor can scan the horizontal inner cavity wall of the mold copper plate to detect data. 4. Vertical mechanical power output unit: the digital servo motor in the vertical direction controls the sensor to move in the vertical direction, so that the sensor can scan the vertical cavity wall of the mold copper plate to detect data. 5. Instrument motion control unit: It is used to control the motion scanning of the motor, and the running speed, running track, and control mode of the motor can be configured through parameter settings. 6. Laser measurement sensor: The laser displacement sensor adopts the principle of laser triangulation. The laser transmitter shoots the visible infrared laser to the surface of the measured object through the lens, and the laser reflected by the object passes through the receiver lens and is received by the internal line array image processing sensor. According to different distances, the corresponding positions of the light spots received on the line array sensor are also different. According to the angle of this reflection, the distance between the actual objects can be calculated by calculating the distance of the sensor spot. 7. Instrument bracket: The mold surface cladding detection equipment need to be placed directly above the mold when it is in use, and it is required to be fixed firmly without displacement vibration during the measurement process to ensure the measurement accuracy. The parameters： Detection instrument service life: ≥5 years; Detection instrument reliability: more than 98%; Detection range: 60~1000mm (customizable) Detection accuracy: 0.01mm Spot diameter: 1.0x1.5mm (spot scan), 1.0x20mm (line scan) Falling pace: 1~20mm/step Single measurement time: less than 2min Power supply: DC24V Operating temperature: -20~80℃ Equipment warm-up time: 3~5min Shock resistance: 50G (X, Y, Z axis) Vibration resistance: 10Hz~5Hz (amplitude 1.5mm, each 2 hours in X, Y, Z axis)

OLIOMIO 50 MONOBLOC EXTRA VIRGIN OLIVE OIL PROCESSING PLANT FORSALE. We have a fully reconditioned Oliomio 50 olive machine setup complete forsale. This machine is capable of processing 50kg's of olive per hour and makes the highest quality olive oil. It is a all in one unit with an upgraded crusher unit same as the newer machines as fitted with and comes with the following: 1. 2 X Stainless steel storage tanks 2. 1x 90 litre gravity filter 3. 1x Stainless steel oil catchment bucket. All the equipment you need to make high quality olive that you need is supplied with this deal. Being the aftersales agents for the last 24 years we are offering free installation and training to make sure you understand how the system works perfectly. This processing setup is R147 900.00 saving from a new machine with the same specifications. This processing setup is an excellent starting point and we will also supply the machine with a 2 year warranty and will offer a buy back only on a trade in on a bigger unit. 1. 100% of this orders value if traded in within 18months 2. 85% of this orders value if traded in 24 months 3. 75% of this orders value if traded in 36months Please contact Piero Cell: 072 1550816 if not avaliable by phone call please leave a whatsapp. Email: piero@viglietti-le.co.za

We have a beautiful Oliomio 150kg per hour Olive oil processing machine with attachments. The machine we have available will be sold fully recondtioned and with the same 2 year warranty supplied by the Mori-TEM factory. This particular unit is the perfect size for production quantites from as low as 500kg per season right up to 80 000kg per season. The machine is fitted with the famous Mori-TEM centrifugal decanter which ensures excellent quality oil extraction and the maximum yield from your olives. The machine is capable of producing Extra virgin olive oil from any cultivar of olives as it has adjustment nostles in the decanter and hydro water control to further reach the extration point. What is nice about this particular machine is that it is very user friendly and able to work continously with small and large quantities of olives. We sell the machine with a 2 year factory warranty and we deliver, install and fully train the owner or operator on the machine by completing a full production and cleaning process. We at Viglietti Lifestyle Estate have been the Importer and Aftersales agents for Mori-TEM since 1997 and work along with Benedetta Lami who is the sole sales agent. The Oliomio and Mori-TEM brands have proven there capabilities throughout south african in making some of the highest quality oil in the country. With this Olive processing setup being already available in South Africa you save hugely on the euro exchange rate and because the Olive Oil prices in South Africa are increasing dramatically (Bulk rate from R140 - R175 per litre) Dont miss this amazing oppotunity! Contact: Piero Viglietti Cell: 0662061076 email: piero@viglietti-le.co.za or Benedetta Lami Cell: 082 559-9190 email: benedetta@oliomio.co.za

The Heat Transfer Equipment Exhibition serves as a premier industry event, spotlighting the latest advancements in thermal processing and heat exchange solutions. Bringing together leading experts and companies, the exhibition fosters discussions on industrial heating, cooling, and energy efficiency. It's a vital hub for discovering innovative technologies, sharing insights, and forging valuable connections within the dynamic realm of heat transfer. Address:-C-17, 2nd Floor, DDA Sheds, Okhla Industrial Area, Phase-I, New Delhi - 110020, INDIA Email:-info@garmenttechnologyexpo.com Phone Number:-7428499699 Website:-https://www.garmenttechnologyexpo.com/exhibitor

BANDSAW SALE-BUTCHER SALE FERTON MEAT BAND SAW FOR SALE MQC 250 WWITH A 3 IN 1 FUNCION MEAT SAW MINCER SAUSAGE STUFFER ***R9499*** J210 BANDSAW COUNTERTOP ***R11499*** J310 BANDSAW COUNTERTOP ***R26999*** J300 BANDSAW FREESTANDING ***R28999*** J360 BANDSAW FREESTANDING ***R38999*** J400 BANDSAW FREESTANDING (BIG BOSS) ***R39499*** All food-contact parts are constructed from food-grade 304 stainless steel, adhering to strict international hygiene standards. ALL PRODUCTS ARE SOLD NEW ND CARRIES A WALK-IN 12MONTH WARRANTY. CONTACT DETAILS CELL/WHATSAPP: 0601446390 PHONE: 0128040231 EMAIL: srcatering582@gmail.com ADDRESS: 96 FASCIA ROAD SILVERTON PRETORIA meat grinder,meat mincer,mince maker, mincer,mincer 52,electric grinders for sale, electric meat grinder, electric meat mincer, electric mincer, Floor Standing, food grinder, food grinder machine, good quality meat grinder, grinder machine meat, grinder specials, industrial meat mincer, industrial mincer, manual meat grinder, meat, Meat grinder, meat grinders for sale, meat machine, Meat Mincer, meat mincer for sale, meat mincer price, meat mincers, meat processing equipment, meat saw and grinder, Mince, mince maker, mince maker machine, mince meat machine price, Mincer, mincer and sausage maker, Mincer Floor Standing, Mincer For Sale, Mincer Machine, Mincer Machine for sale, mincer price, second hand meat grinder for saleButchery Equipment,Meat Processing Equipment,Butcher Tools,Commercial Butchery Equipment,Meat Cutting Machines,Professional Butcher Supplies,Meat Grinder for Sale,Butcher Saw,Meat Slicer,Butcher Knives and Equipment,Meat Tenderizer,Butchery Supplies,Industrial Meat Equipment,Butcher Shop Equipment,Meat Processing Tools,Heavy Duty Butcher Equipment,Meat Bandsaw,Food Processing Equipment for Butchers,Butcher Shop Machinery,Commercial Meat Grinder,Processing Equipment,Top Rated Butcher Knives for Professional Use,Heavy Duty Meat Slicer for Restaurants,Butcher Shop Equipment,beef sausage recipes, boerewors making machine, boerewors making machine for sale, Electric Sausage Filler, Filler Hydraulic, how to make sausage, industrial sausage filler, industrial sausage making machine, mincer and sausage maker, Rapid Filler, sausage casing, Sausage Filler, Sausage Filler For Sale, sausage filling machine, sausage machine, sausage machine for sale, sausage maker, sausage maker for sale, sausage maker price, sausage making machine, sausage stopper, sausage stuffer price, sausage stuffing, sausage suffer, vertical sausage filler, wors machine, wors machine for sale, wors making machineMeat Bandsaw for Sale,Commercial Meat Bandsaw,Heavy Duty Meat Bandsaw,Industrial Meat Bandsaw,Best Meat Bandsaw,Meat Cutting Bandsaw,Professional Meat Bandsaw,Affordable Meat Bandsaw,High-Quality Meat Bandsaw,Meat Bandsaw Machine,Meat Bandsaw Blade,Buy Meat Bandsaw,Meat Bandsaw Equipment,Top Rated Meat Bandsaw,Meat Bandsaw for Butcher Shop,Meat Bandsaw Reviews,Durable Meat Bandsaw,Meat Bandsaw Deals,Meat Bandsaw Supplier,Heavy Duty Meat Cutter Bandsaw.Pretoria,johannesburg,pretoria east,pretoria west,kokstad,mamelodi,near me Pictures used for illustration purposes and products colours and style may vary. Stock ID: bandsaw nc xarnarvon

BANDSAW SALE-BUTCHER SALE FERTON MEAT BAND SAW FOR SALE MQC 250 WWITH A 3 IN 1 FUNCION MEAT SAW MINCER SAUSAGE STUFFER ***R9499*** J210 BANDSAW COUNTERTOP ***R11499*** J310 BANDSAW COUNTERTOP ***R26999*** J300 BANDSAW FREESTANDING ***R28999*** J360 BANDSAW FREESTANDING ***R38999*** J400 BANDSAW FREESTANDING (BIG BOSS) ***R39499*** All food-contact parts are constructed from food-grade 304 stainless steel, adhering to strict international hygiene standards. ALL PRODUCTS ARE SOLD NEW ND CARRIES A WALK-IN 12MONTH WARRANTY. CONTACT DETAILS CELL/WHATSAPP: 0601446390 PHONE: 0128040231 EMAIL: srcatering582@gmail.com ADDRESS: 96 FASCIA ROAD SILVERTON PRETORIA meat grinder,meat mincer,mince maker, mincer,mincer 52,electric grinders for sale, electric meat grinder, electric meat mincer, electric mincer, Floor Standing, food grinder, food grinder machine, good quality meat grinder, grinder machine meat, grinder specials, industrial meat mincer, industrial mincer, manual meat grinder, meat, Meat grinder, meat grinders for sale, meat machine, Meat Mincer, meat mincer for sale, meat mincer price, meat mincers, meat processing equipment, meat saw and grinder, Mince, mince maker, mince maker machine, mince meat machine price, Mincer, mincer and sausage maker, Mincer Floor Standing, Mincer For Sale, Mincer Machine, Mincer Machine for sale, mincer price, second hand meat grinder for saleButchery Equipment,Meat Processing Equipment,Butcher Tools,Commercial Butchery Equipment,Meat Cutting Machines,Professional Butcher Supplies,Meat Grinder for Sale,Butcher Saw,Meat Slicer,Butcher Knives and Equipment,Meat Tenderizer,Butchery Supplies,Industrial Meat Equipment,Butcher Shop Equipment,Meat Processing Tools,Heavy Duty Butcher Equipment,Meat Bandsaw,Food Processing Equipment for Butchers,Butcher Shop Machinery,Commercial Meat Grinder,Processing Equipment,Top Rated Butcher Knives for Professional Use,Heavy Duty Meat Slicer for Restaurants,Butcher Shop Equipment,beef sausage recipes, boerewors making machine, boerewors making machine for sale, Electric Sausage Filler, Filler Hydraulic, how to make sausage, industrial sausage filler, industrial sausage making machine, mincer and sausage maker, Rapid Filler, sausage casing, Sausage Filler, Sausage Filler For Sale, sausage filling machine, sausage machine, sausage machine for sale, sausage maker, sausage maker for sale, sausage maker price, sausage making machine, sausage stopper, sausage stuffer price, sausage stuffing, sausage suffer, vertical sausage filler, wors machine, wors machine for sale, wors making machineMeat Bandsaw for Sale,Commercial Meat Bandsaw,Heavy Duty Meat Bandsaw,Industrial Meat Bandsaw,Best Meat Bandsaw,Meat Cutting Bandsaw,Professional Meat Bandsaw,Affordable Meat Bandsaw,High-Quality Meat Bandsaw,Meat Bandsaw Machine,Meat Bandsaw Blade,Buy Meat Bandsaw,Meat Bandsaw Equipment,Top Rated Meat Bandsaw,Meat Bandsaw for Butcher Shop,Meat Bandsaw Reviews,Durable Meat Bandsaw,Meat Bandsaw Deals,Meat Bandsaw Supplier,Heavy Duty Meat Cutter Bandsaw.Pretoria,johannesburg,pretoria east,pretoria west,kokstad,mamelodi,near me Pictures used for illustration purposes and products colours and style may vary. Stock ID: bandsaw pta bronk

BANDSAW SALE-BUTCHER SALE FERTON MEAT BAND SAW FOR SALE MQC 250 WWITH A 3 IN 1 FUNCION MEAT SAW MINCER SAUSAGE STUFFER ***R9499*** J210 BANDSAW COUNTERTOP ***R11499*** J310 BANDSAW COUNTERTOP ***R26999*** J300 BANDSAW FREESTANDING ***R28999*** J360 BANDSAW FREESTANDING ***R38999*** J400 BANDSAW FREESTANDING (BIG BOSS) ***R39499*** All food-contact parts are constructed from food-grade 304 stainless steel, adhering to strict international hygiene standards. ALL PRODUCTS ARE SOLD NEW ND CARRIES A WALK-IN 12MONTH WARRANTY. CONTACT DETAILS CELL/WHATSAPP: 0601446390 PHONE: 0128040231 EMAIL: srcatering582@gmail.com ADDRESS: 96 FASCIA ROAD SILVERTON PRETORIA meat grinder,meat mincer,mince maker, mincer,mincer 52,electric grinders for sale, electric meat grinder, electric meat mincer, electric mincer, Floor Standing, food grinder, food grinder machine, good quality meat grinder, grinder machine meat, grinder specials, industrial meat mincer, industrial mincer, manual meat grinder, meat, Meat grinder, meat grinders for sale, meat machine, Meat Mincer, meat mincer for sale, meat mincer price, meat mincers, meat processing equipment, meat saw and grinder, Mince, mince maker, mince maker machine, mince meat machine price, Mincer, mincer and sausage maker, Mincer Floor Standing, Mincer For Sale, Mincer Machine, Mincer Machine for sale, mincer price, second hand meat grinder for saleButchery Equipment,Meat Processing Equipment,Butcher Tools,Commercial Butchery Equipment,Meat Cutting Machines,Professional Butcher Supplies,Meat Grinder for Sale,Butcher Saw,Meat Slicer,Butcher Knives and Equipment,Meat Tenderizer,Butchery Supplies,Industrial Meat Equipment,Butcher Shop Equipment,Meat Processing Tools,Heavy Duty Butcher Equipment,Meat Bandsaw,Food Processing Equipment for Butchers,Butcher Shop Machinery,Commercial Meat Grinder,Processing Equipment,Top Rated Butcher Knives for Professional Use,Heavy Duty Meat Slicer for Restaurants,Butcher Shop Equipment,beef sausage recipes, boerewors making machine, boerewors making machine for sale, Electric Sausage Filler, Filler Hydraulic, how to make sausage, industrial sausage filler, industrial sausage making machine, mincer and sausage maker, Rapid Filler, sausage casing, Sausage Filler, Sausage Filler For Sale, sausage filling machine, sausage machine, sausage machine for sale, sausage maker, sausage maker for sale, sausage maker price, sausage making machine, sausage stopper, sausage stuffer price, sausage stuffing, sausage suffer, vertical sausage filler, wors machine, wors machine for sale, wors making machineMeat Bandsaw for Sale,Commercial Meat Bandsaw,Heavy Duty Meat Bandsaw,Industrial Meat Bandsaw,Best Meat Bandsaw,Meat Cutting Bandsaw,Professional Meat Bandsaw,Affordable Meat Bandsaw,High-Quality Meat Bandsaw,Meat Bandsaw Machine,Meat Bandsaw Blade,Buy Meat Bandsaw,Meat Bandsaw Equipment,Top Rated Meat Bandsaw,Meat Bandsaw for Butcher Shop,Meat Bandsaw Reviews,Durable Meat Bandsaw,Meat Bandsaw Deals,Meat Bandsaw Supplier,Heavy Duty Meat Cutter Bandsaw.Pretoria,johannesburg,pretoria east,pretoria west,kokstad,mamelodi,near me Pictures used for illustration purposes and products colours and style may vary. Stock ID: bandsaw east r springs

BANDSAW SALE-BUTCHER SALE FERTON MEAT BAND SAW FOR SALE MQC 250 WWITH A 3 IN 1 FUNCION MEAT SAW MINCER SAUSAGE STUFFER ***R9499*** J210 BANDSAW COUNTERTOP ***R11499*** J310 BANDSAW COUNTERTOP ***R26999*** J300 BANDSAW FREESTANDING ***R28999*** J360 BANDSAW FREESTANDING ***R38999*** J400 BANDSAW FREESTANDING (BIG BOSS) ***R39499*** All food-contact parts are constructed from food-grade 304 stainless steel, adhering to strict international hygiene standards. ALL PRODUCTS ARE SOLD NEW ND CARRIES A WALK-IN 12MONTH WARRANTY. CONTACT DETAILS CELL/WHATSAPP: 0601446390 PHONE: 0128040231 EMAIL: srcatering582@gmail.com ADDRESS: 96 FASCIA ROAD SILVERTON PRETORIA meat grinder,meat mincer,mince maker, mincer,mincer 52,electric grinders for sale, electric meat grinder, electric meat mincer, electric mincer, Floor Standing, food grinder, food grinder machine, good quality meat grinder, grinder machine meat, grinder specials, industrial meat mincer, industrial mincer, manual meat grinder, meat, Meat grinder, meat grinders for sale, meat machine, Meat Mincer, meat mincer for sale, meat mincer price, meat mincers, meat processing equipment, meat saw and grinder, Mince, mince maker, mince maker machine, mince meat machine price, Mincer, mincer and sausage maker, Mincer Floor Standing, Mincer For Sale, Mincer Machine, Mincer Machine for sale, mincer price, second hand meat grinder for saleButchery Equipment,Meat Processing Equipment,Butcher Tools,Commercial Butchery Equipment,Meat Cutting Machines,Professional Butcher Supplies,Meat Grinder for Sale,Butcher Saw,Meat Slicer,Butcher Knives and Equipment,Meat Tenderizer,Butchery Supplies,Industrial Meat Equipment,Butcher Shop Equipment,Meat Processing Tools,Heavy Duty Butcher Equipment,Meat Bandsaw,Food Processing Equipment for Butchers,Butcher Shop Machinery,Commercial Meat Grinder,Processing Equipment,Top Rated Butcher Knives for Professional Use,Heavy Duty Meat Slicer for Restaurants,Butcher Shop Equipment,beef sausage recipes, boerewors making machine, boerewors making machine for sale, Electric Sausage Filler, Filler Hydraulic, how to make sausage, industrial sausage filler, industrial sausage making machine, mincer and sausage maker, Rapid Filler, sausage casing, Sausage Filler, Sausage Filler For Sale, sausage filling machine, sausage machine, sausage machine for sale, sausage maker, sausage maker for sale, sausage maker price, sausage making machine, sausage stopper, sausage stuffer price, sausage stuffing, sausage suffer, vertical sausage filler, wors machine, wors machine for sale, wors making machineMeat Bandsaw for Sale,Commercial Meat Bandsaw,Heavy Duty Meat Bandsaw,Industrial Meat Bandsaw,Best Meat Bandsaw,Meat Cutting Bandsaw,Professional Meat Bandsaw,Affordable Meat Bandsaw,High-Quality Meat Bandsaw,Meat Bandsaw Machine,Meat Bandsaw Blade,Buy Meat Bandsaw,Meat Bandsaw Equipment,Top Rated Meat Bandsaw,Meat Bandsaw for Butcher Shop,Meat Bandsaw Reviews,Durable Meat Bandsaw,Meat Bandsaw Deals,Meat Bandsaw Supplier,Heavy Duty Meat Cutter Bandsaw.Pretoria,johannesburg,pretoria east,pretoria west,kokstad,mamelodi,near me Pictures used for illustration purposes and products colours and style may vary. Stock ID: bandsaw potch

Requirements: · Minimum 2 years experience working in a beverage production plant environment / dairy industry · Experience operating pasteurizer or processing equipment Salary is market related Please note: if you have not been contacted within 2 weeks consider your application unsuccessful

Port ElizabethTo lead a software team – to develop a number of applications to enhance business. An interest in machines, mechatronics etc would be ideal. The company has a plan to invest in the world best processing equipment and need a bright, sharp mind to assist them to integrate these machines and develop applications that will make them the number one processor in the country. This company is progressive within the industry by bringing innovative ways for their customers to order specific products using one button and ensuring they receive it perfect every time ! The long term run way for this candidate is to get exposure and access to some of the best European machine manufacturers which can connect them with and provide programmes for bright minds to get exposure to the international stage.Skill set required:FlutterC#SQLPHPOther Beneficial Skills:.Net Framework..Net Visual Studio.Agile and Scrum.AJAX.Android Studio.AppScan.ASP.Net.Azure.C#.Crystal.CSS.Entity framework.Flutter.GitLab.HTML.JavaScript.JQuery.Microsoft Office.Microsoft Visual Studio.MS Office.MVC.MySQL.PHP.Python.SQL - Server & Server Management.Syspro.Team Foundation Server.Telerik Reports.Testing UI.TFS source control.Uipath Studio.VB.Visual Studio.WCF.WPF.Xamarin Android (Beginner).XAML.Requirements:BSC Computer Science and Applied Mathematics Degree.Matric.Driver's License.8+ years of experience as a Senior Automation Developer.Excellent leadership skills and the ability to lead and drive a team in new innovation!

Purpose of the role: To lead a software team – to develop a number of applications to enhance business. An interest in machines, mechatronics etc would be ideal. The company has a plan to invest in the world best processing equipment and need a bright, sharp mind to assist them to integrate these machines and develop applications that will make them the number one processor in the country. This company is progressive within the industry by bringing innovative ways for their customers to order specific products using one button and ensuring they receive it perfect every time ! The long term run way for this candidate is to get exposure and access to some of the best European machine manufacturers which can connect them with and provide programmes for bright minds to get exposure to the international stage. Skill set required: Flutter. C#. SQL. PHP. Other Beneficial Skills:.Net Framework..Net Visual Studio. Agile and Scrum. AJAX. Android Studio. AppScan. ASP.Net. Azure. C#. Crystal. CSS. Entity framework. Flutter. GitLab. HTML. JavaScript. JQuery. Microsoft Office. Microsoft Visual Studio. MS Office. MVC. MySQL. PHP. Python. SQL - Server & Server Management. Syspro. Team Foundation Server. Telerik Reports. Testing UI. TFS source control. Uipath Studio. VB. Visual Studio. WCF. WPF. Xamarin Android (Beginner). XAML. Requirements: BSC Computer Science and Applied Mathematics Degree. Matric. Driver''s License. 8+ years of experience as a Senior Automation Developer. Excellent leadership skills and the ability to lead and drive a team in new innovation! Please consider your application unsuccessful should you not receive a response within 2 weeks of applying.

Overview Mold is the casting billet forming equipment in continuous steel casting, and it is also the core equipment and key technology of continuous casting machine. Its function is to forcibly cool the high-temperature molten steel continuously injected into its inner cavity through the water-cooled copper plate to export its heat and to gradually solidify it into a casting billet with the required cross-sectional shape and billet shell thickness. And the casting billet, which is still in liquid state, is continuously pulled out from the lower nozzle of the mold to create conditions for casting billet to be completely solidified in the subsequent secondary cooling area. The main function of the mould oscillation device is to make the mould perform mechanical movement according to the given characteristics of amplitude, frequency and waveform deflection. The purpose is to facilitate demoulding and prevent the occurrence of sticking and breakout accidents due to the bonding of the casting billet with the copper wall of the mold during the solidification process. MOC-K100 mould oscillation online monitoring system can three-dimensionally detect the positive and negative frequencies and waveform characteristics of the mould oscillation. The online changing data is provided in real time, which provides convenient and effective detection methods for on-site inspection personnel. The meaning of the system 1. When the continuous casting machine is not working properly, the billet quality problems (such as unstable oscillation marks, edge cracks, etc.) occur. According to the monitoring results of the system, we can combine with the actual on- site situation to analyze the cause of the failure, and efficiently evaluate and solve the problem of the oscillation table to improve product quality. 2. During the normal operation of the equipment, with the fatigue and wear of the mechanical structure of the mold, the expected oscillation parameters of the mold and the actual oscillation parameters will have a oscillation difference with time change, resulting in the internal process parameters’ changing of the continuous casting machine. Timely and accurate monitoring of changes in these parameters is helpful to schedule maintenance. 3. Transfer equipment maintenance from regular maintenance to state maintenance, do not repair when there is no problem, and arrange maintenance according to production needs when abnormal signs appear. Prevent over-repair and under-repair. 4. According to the monitoring results of the equipment, the on-site working parameters are adjusted in time to avoid adopting inaccurate or large-error oscillation to work and prevent the "breakout" accident. 5. We can timely find out that the oscillation is not stable or out of control in a small range, so as to avoid the formation of unevenness and unstable oscillation marks on the surface of the slab during the solidification of molten steel into the slab, and improve the surface quality of the product. 6. Adjust the working parameters reasonably according to the monitoring results, avoiding the use of excessive safety factor, making the entire assembly line play a normal working efficiency, increasing the output of billets, and create favorable conditions for increasing the casting speed. The functions of the system (1) Overview of monitoring parameters: Provides an overview of real-time monitoring parameters in the full screen, displaying all real-time data including oscillation parameters and process parameters. (2) Time domain waveform: This function mainly displays the oscillation waveforms of multiple measuring points and one channel standard waveform in real time, and simultaneously displays the three elements of oscillation of each measuring point in real time. (3) Waveform superposition: The difference between this function and the time domain waveform is that the waveforms of multiple measuring points are superimposed on a graph with lines of different colors on the same scale, and the oscillation difference of each channel can be calculated and displayed intuitively. (4) FFT: This functional module completes the calculation and display of the oscillation spectrum in real time. It is used to evaluate the waveform distortion of the entire oscillation table and to determine whether there is a problem with the installation of the oscillation device. (5) Bar graph: The oscillation of each measuring point is indicated by a bar graph of peak value and sensor gap voltage, which is more intuitive. (6) Trend: After starting this module, the operator can search the historical records in the database, analyze the changing trend of each parameter, and use it to analyze the rationality of the steel quality and processing parameter settings for different steels under the oscillation conditions. The parameters of the system 1. Number of measurement channels: According to the mold design, up to 16 sensors can be arranged 2. Sensor: three-dimensional oscillation sensing (X, Y, Z three axes) 3. Sensitivity: 1000mV/g 4. Frequency range: 0.04~10HZ 5. Frequency accuracy: ±0.01 Hz 6. Amplitude accuracy: 0.005mm 7. Transmission mode: wired digital transmission, wireless transmission 8. Host: 3U standard rack, handheld device 9. Sensor power supply: 24V.DC 10. Host power supply: 220V.AC/50Hz Mold oscillation curve The structure of the system The main components of the continuous casting mould online oscillation detection system are: 1. Three-dimensional oscillation measurement sensor 2. Handheld oscillation sensor calibrator 3. Dedicated signal connection cable 4. Preamplifier 5. Operation processing unit 6. Graphic display terminal 7. Industrial Ethernet (TCP/IP) or PROFIBUS-DP communication components 8. Control cabinet

Overview The surface quality inspection of high temperature cast product is of great significance to the repair of cast product’s defects and the hot delivery of hot cast product. The ZSQ-T series of online surface quality inspection equipment for casting billets developed by Wuhan CenterRise M&C Engineering Co., Ltd can detect the defects such as scratches, cracks, holes, pits, edge cracks, edge defects on the surface of the cast products, and meet the customer's requirements for the quality inspection of the surface of the cast product. The principle of the system The ZSQ-T200 online surface quality inspection system for continuously cast products adopts the principle of optical imaging and uses a CCD image sensor to input the surface image of the cast products to be detected into the computer, and then the obtained image is processed by special image processing software to find out whether there is any defect in the image. After the defects in the image are obtained, the obtained defects are classified through a special self-learning system, and finally the requirements of the computer to automatically identify the surface defects of the cast products are achieved. The composition of the system 1. Optical part: The optical part is composed of multiple fixed-focus lenses and linear CCD, which mainly realizes scanning and imaging of the surface of the cast products. 2. Lighting part: The lighting part is composed of a high-brightness LED array and a cylindrical lens, which realizes high-brightness and high-uniformity lighting on the surface of the cast products. 3. Mechanical structure part: The mechanical structure part mainly realizes the adjustment, installation and fixing of the optical part and the lighting part, and consists of the imaging head (optical part), light box (lighting part), bracket and control cabinet. The structure is required to be stable and reliable. 4. Real-time processing: The real-time processing part is completed by the multi-CCD data real-time sampling processing unit (high-speed DSP) independently developed by Wuhan CenterRise M&C Engineering Co., Ltd. 5. Hardware part: The hardware part consists of high-speed storage controller and storage hard disk array, Gigabit InternetMAC controller, Gigabit Ethernet PHY. Rj45, and multiple high-speed workstations. 6. Detection software: The detection software mainly realizes the functions of collection, storage, transmission, processing of CCD scanning images, extraction of defects, analysis of defect characteristics, calculation of defect size and position, storage of defect images, generation of cast product’s surface quality analysis reports. etc.

Job Position: Refrigeration Technician Ref: 3480 - Edwin Location: Port Elizabeth Salary: R17 000 to R23 000 per month + Provident Fund Shift work – 4 am to 12 pm / 12 pm to 8 pm / 8 pm to 4 am Qualifications / Requirements Trade tested Qualified Artisan certificate essential Ammonia Safe Handling Certificate essential Minimum of 2 years experience in ammonia refrigeration maintenance, preferably in a FMCG processing environment Knowledge of FMCG equipment operation and maintenance Willing to work shifts Must have own transport and valid drivers license Have own basic tools needed to perform the function of Refrigeration Technician Good interpersonal skills Good planning and organizational skills Pay attention to detail Stress tolerance Flexibility and adaptability with regards to breakdowns and working hours Key Performance Areas: 3 % downtime in order to contribute to achieve targeted throughput Conduct preventative maintenance 100 % execution of job cards allocated 100 % accurate job card administration Adherence to manufacturers service schedules Adhere to communicated SOP’s which relates to maintenance and the operations thereof Eliminate wastage Zero (0%) reworks 100% adherence to the time and attendance procedure Responsibility: Qualifications / Requirements Trade tested Qualified Artisan certificate essential Ammonia Safe Handling Certificate essential Minimum of 2 years experience in ammonia refrigeration maintenance, preferably in a FMCG processing environment Knowledge of FMCG equipment operation and maintenance Willing to work shifts Must have own transport and valid drivers license Have own basic tools needed to perform the function of Refrigeration Technician Good interpersonal skills Good planning and organizational skills Pay attention to detail Stress tolerance Flexibility and adaptability with regards to breakdowns and working hours Key Performance Areas: 3 % downtime in order to contribute to achieve targeted throughput Conduct preventative maintenance 100 % execution of job cards allocated 100 % accurate job card administration Adherence to manufacturers service schedules Adhere to communicated SOP’s which relates to maintenance and the operations thereof Eliminate wastage Zero (0%) reworks 100% adherence to the ti Salary: R17000 to 23000 Job Reference #: Refrigeration Technician

Overview The continuous casting vibration type ladle slag detection device is used to detect the slag content of the ladle nozzle in the steelmaking continuous casting process, so as to improve the cleanliness of the tundish molten steel and obtain the best yield of the ladle molten steel. The device adopts the principle of vibration detection. The LAG-S200 continuous casting ladle slag automatic detection system is developed by Wuhan CenterRise M&C Engineering Co., Ltd. after many years of research with many scientific research institutes, and fully combined with the actual situation on site. It has a real field application value as a continuous casting ladle slag automatic detection system. The meaning of the system 1. Reduce the amount of tundish slag 2. Improve the purity of molten steel 3. Improve the life of the tundish 4. Reduce sliding nozzle erosion 5. Reduce nozzle blockage 6. Increase continuous pouring heats 7. Reduce the amount of residual steel in the ladle when high-quality steel is casting 8. Improve the yield of molten steel 9. Improve the quality of continuous casting billets In order to improve the purity of the molten steel in the tundish, and improve the quality of the casting billet, especially to improve the quality of the billet in the transition section, and reduce the amount of residual steel in the high-quality ladle, and prolong the life of the tundish lining, and increase the continuous casting heats, it’s necessary to detect and control the slag in the later stage of continuous casting ladle casting. The working principle The LAG-S200 continuous casting ladle slag automatic monitoring system detects the slag state during the pouring process by receiving the vibration signal of the mechanical operating arm of the ladle nozzle. In the process of molten steel pouring, when molten steel flows through the long nozzle and pours into the tundish, the molten steel impacts the wall of the long nozzle and causes the vibration of the mechanical operating arm used to support the long nozzle. Since the specific gravity of the steelmaking slag is less than half of the specific gravity of the molten steel, it floats on the surface of the molten steel, and the steelmaking slag appears when the molten steel is about to be all poured. At this time, due to the high viscosity and poor fluidity of light steelmaking slag, the impact force of the mixed flow of molten steel and steel slag on the wall of the long nozzle is quite different from that of pure molten steel. The system mainly monitors the ladle slag of the continuous casting by measuring and analyzing the vibration difference of the mechanical operating arm. The vibration signal is connected to the operation control unit of the system control cabinet through the front-stage conditioning and amplification module through the sensor installed in the middle of the operating rod. After processing, it is output to the industrial computer for operation and analysis. The slag signal detected by the system is output from the system control cabinet to the front-end control unit, and then control the alarm horn and alarm light to work, or issue an instruction to close the ladle nozzle. The features of the system (1) It is easy to install, basically no modification is made to the field equipment, and the installation and debugging work will not affect the normal production of the enterprise. (2) The detection accuracy is high, and the effective rate is greater than or equal to 95%. The threshold of slag volume is accurately set, the output control function is powerful. It has excellent performance in technical indicators such as the sensor service life and sensor usage times. (3) The sensor is installed at a position far away from the molten steel, and is cooled by a special refrigeration device for 24 hours. The outer layer adopts a composite protection structure, which has a long service life. (4) Adopt professional and targeted signal processing methods to obtain the vibration characteristic parameters of the ladle slag, and analyze, reason and judge the effective slag signal through the vibration signal database, which has a high accuracy of slag alarm. (5) The architecture is established based on the artificial intelligence network, which has the functions of self-learning and self-induction. (6) The equipment adopts a modular design. The failure of each module will not affect other parts, which ensure more reliable operation of the system and easy maintenance. (7) The alarm display device is used on site to visually indicate the flow state of molten steel and slag. When slag carryover strats, we can choose automatic mode or manual mode. In both modes, the system will give audible and visual alarm signals to remind on-site operators. (8) The system has a powerful database function. Including the comparison function for last two ladles of casting time record, the system automatically stores the running data, and generates a record file every day. (9) The system has the function of automatically controlling the ladle nozzle. The control unit is an auxiliary system of the system, which is interconnected with the ladle slag detection system to automatically control the opening of the ladle nozzle and realize the whole-process control of the liquid level of the molten steel in the tundish. The composition of the system The LAG-S200 slag detection system consists of: vibration detection sensor, pre-signal amplifier, slag detection operation unit, tundish liquid level control unit, on-site operation indication box, and process control cabinet. 1. Vibration detection sensor: It is installed on the robotic arm of the stopper to detect the vibration signal of the whole casting process of the ladle. 2. Pre-signal amplifier: Amplify, convert and transmit the weak vibration signal detected by the vibration detection sensor. 3. Slag detection operation unit: Analyze, judge and discriminate the vibration signal to realize the discrimination of all steel, mixed slag and full slag , and output the slag alarm signal. 4. Tundish liquid level control unit: Accept the control signal of the tundish nozzle and the ladle nozzle, and realize automatic or manual control to the ladle slag according to the requirements. 5. On-site operation instruction box: Provides man-machine exchange for slag alarm indication, fault indication, system activation mode selection, and control mode selection. 6. Process control cabinet, providing power management, displaying man-machine interface and setting management. The parameters of the system 1. The system controls the slag inclusion in molten steel with high precision and closes the nozzle in real time. 2. Improve the quality of steel, reduce defective products, and improve the yield. 3. The yield of molten steel is increased by 0.3%-0.5%. The nozzle can be automatically closed, so that the disadvantage of untimely manual response is overcome and less molten steel remains in the ladle. The threshold value of molten steel (slag threshold) is set by the user within a wide range. 4. No artificial factors are involved, high reliability, good repeatability or consistency. 5. The steelmaking slag does not pass through or rarely flows into the tundish, which increases the service life of the refractory material and the sliding nozzle. 6. Reduce the blockage of the tundish nozzle and increase the number of continuous pouring heats of the tundish.

Minimum Requirements: Grade 12 certificate or relevant NQF level 4 qualification Mechanical Trade Test Certificate Minimum 5 years’ work experience in skilled trades in the mining / blasting industry Experience in or knowledge of the blasting industry an advantage Experience in a Concentrator Plant will be advantageous Minimum 5 years’ experience as a Maintenance Planner Advance Computer skills required with high attention to detail, logic and numeracy Computerized Maintenance Management System Microsoft Office (Excel, Word, Outlook, PowerPoint) Computerised Maintenance Management System Microsoft Project Management Software Skills Must have relevant Planned Maintenance training Ability to Conduct Root Cause Failure analysis Strong Communication Skills Ability to multi-task Organizational and Time Management Skills A valid driver’s license and a medical certificate of fitness required Some level of Supervisory experience Must be fit to undergo and pass a medical examination which must include an eye sight, depth perception and hearing test Duties & Responsibilities: To initiate, populate, manage and maintain master data relating to planned preventative maintenance using the Sage System To improve work force productivity and work quality by anticipating and eliminating potential delays through planning and coordination of labor, parts and material, and equipment access Effective operation of business area Planned Maintenance Programme Schedule maintenance for equipment to agreed standards, in agreement with line management Monitor maintenance feedback from business area for conformance to plan and ability to highlight important variances to management Assist with all administrative related tasks Continuously issuing of PM orders timeously to Foreman per site Continuously liaise with the relevant Foreman on planned maintenance activities and resources Assist with planning and scheduling of major maintenance related stoppages Determine the priority of work planned in backlog and allocate resources together with the responsible Line Manager Identify opportunities to improve operations by analyzing maintenance and trends Prepare performance reports Maintain data base of maintenance related work instructions and procedures Ensure that the system is maintained and updated as changes to equipment are made or newly installed equipment Knowledge of the principles and concepts of maintenance work Maintain the stores (receiving and dispatches of stock to site) Processing of orders on sage according to procedure and within specified timeframe

INTRODUCTION A leading dynamic Animal Feed Manufacturing business in Mpumalanga, existing for more than 30 years, are looking for a factory manager. We are responsible for producing animal feed to local clients in the monogastric and ruminant fields. JOB PURPOSE Manages the various production activities through subordinates in order to achieve planned production targets and to ensure the effective use of available resources. REQUIREMENTS Relevant production qualification of animal feed plant or a mill plant. Must have at least 2 years hands on experience in feed production and or maintenance and a minimum of 2 years in a production management position with related plant managing a team of operators. Valid driver’s license, willing to relocate, between 30 and 40 years of age. Must have experience in ensuring safety, health & hygiene in a production environment. Minimum Gr12 and speaking Zulu would be advantageous. DUTIES AND RESPONSIBILITIES Leading a team that is responsible for the total production function in terms of functional responsibilities of all equipment. Aligning, guiding and co-coordinating the activities of a team to utilize the skills and experience of each team member to achieve targets in terms of production volumes, quality, uptime, safety, costs and staff development. To keep management up to date of all risk, plant, equipment, people and quality issues Accomplishes manufacturing results by communicating job expectations, planning, monitoring and appraising job results, disciplining employees, initiating, coordinating, and enforcing systems policies and procedures. Maintains workflow by monitoring steps of the process, setting processing variables, observing control points and equipment, monitoring personnel and resources, studying methods, implementing cost reductions, facilitating corrections to malfunctions, within process control points. Completes production plan by scheduling and assigning personnel, accomplishing work results, establishing priorities, monitoring progress, resolving problems, reporting results on production sheets. Maintains quality requirements by establishing and enforcing standards Maintains a safe and clean working environment, maintains compliance with established policies and procedures. Daily monitoring of actual production against the planned targets Identifying and reporting quality problems to the CEO. Taking full responsibilities for the entire plant’s functions Ensure efficient collaboration and co-ordination between all departments including maintenance, production, procurement, sales and distribution. May also need to assist the maintenance technician if required from time to time.

A steel Fabrication and Processing company is looking for an experienced Transport Workshop Manager for their factory in the Delmas area – Mpumalanga/Far East Rand Responsibilities · Overall Fleet Management · Overall Budget Management combined with strategic market review of comparative part pricing structures · General maintenance management of company structures and gardens · Manage Troubleshooting and repair schedules of overall facility machinery · General maintenance management at CEO, MD and or Director’s properties · Responsible for installation, repair, maintenance, preventative maintenance and service of all facility machinery equipment, including Overhead Cranes, Plasma Machine, Workshop saws, Generator etc · Overall diesel usage, planning, reporting and refill management · Employee management, including Project support, employee coordination and time management · Maintain, compile and update standard operating procedures (SOP) · Manage daily maintenance and repair logs of fleet and machinery aligned with Job card planning and allocation · Managing cleaning and maintaining of work areas and company vehicles · Managing equipment when not in use including decommissioning planning · Managing Fleet Planning and route scheduling · Managing overall fleet service schedules and planning thereof so as to minimize downtime · Responsible for operating and monitoring the company vehicles Tracking systems · Managing departmental tools and equipment in department · Managing standby and 24-Hour assistance when required · Maintaining valid licenses, lifting certificates, Permits for company Fleet - Trucks, Trailers, Bakkies etc. · Monitoring and managing driver compliance with road traffic legislation and relevant vehicle usage Requirements · NQF level 7 Business Management qualification (B-Com Management preferred) · Post graduate fleet management qualification (NQF level 8) or Senior Management program in fleet Management · Red Seal Qualified Diesel Mechanic · 6 TO 10 Years Diesel Mechanic experience within a Crane Lifting and Transportation environment combined · 10 to 15 Years proven track record in Senior Management position within similar environment · Minimum of 3 – 5 Year Budget Management experience · Advanced MS Office skills, including PowerPoint · Valid South Africa Drivers Licence · Salary R45 000 to R55 000 Cost to company per month – subject to experience and skillset · SA Citizens only Send complete and updated CV to admin@kencorp.co.za

WWW.BUTCHERYEQUIPMENTSALE.CO.ZA SUPPLIES ONLY THE FINEST QUALITY SAUSAGE MAKING MACHINES TO THE BUTCHERY & MEAT PROCESSING INDUSTRY @ WHOLESALE PRICES DIRECT TO THE PUBLIC !!! CALL / WHATSAPP US NOW ON 082 666 6619 TO AVOID DISAPPOINTMENT !!! WE HAVE THE FOLLOWING SAUSAGE FILLERS IN STOCK & READY FOR PURCHASE WITH SAME DAY DELIVERY: – SAUSAGE FILLER FOR SALE: – 1.MANUAL SAUSAGE FILLER (BOWL VOLUME: 3 LITRES) @ R 2 399.00 (WITH X 4 STAINLESS STEEL NOZZLES) 2. MANUAL SAUSAGE FILLER (BOWL VOLUME: 5 LITRES) @ R 2 899.00 (WITH X 4 STAINLESS STEEL NOZZLES) 3. MANUAL SAUSAGE FILLER (BOWL VOLUME: 7 LITRES) @ R 3 499.00 (WITH X 4 STAINLESS STEEL NOZZLES) 4. MANUAL SAUSAGE FILLER (BOWL VOLUME: 10 LITRES) @ R 4 499.00 (WITH X 4 STAINLESS STEEL NOZZLES) 5. MANUAL SAUSAGE FILLER (BOWL VOLUME: 15 LITRES) @ R 5 499.00 (WITH X 4 STAINLESS STEEL NOZZLES) 6. ELECTRIC SAUSAGE MAKER (BOWL VOLUME: 10 LITRES) @ R 14 999.00 (WITH X 4 STAINLESS STEEL NOZZLES) 7. ELECTRIC SAUSAGE MAKER (BOWL VOLUME: 15 LITRES) @ R 19 999.00 (WITH X 4 STAINLESS STEEL NOZZLES) 8. HYDRAULIC SAUSAGE FILLER (PRODUCTIVITY: 400 KG PER HOUR) / (BOWL VOLUME: 26 LITRES) @ R 37 499.00 ALL OF OUR BUTCHERY EQUIPMENT IS SOLD BRAND NEW & CARRY A WARRANTY PERIOD OF 6/12 MONTHS. CALL / WHATSAPP US ON 082 666 6619 OR MAKE AN APPOINTMENT TO VISIT OUR SHOWROOM AT: – 05 BONANZA STREET SELBY JOHANNESBURG GAUTENG OR VISIT OUR WEBSITE ON www.butcheryequipmentsale.co.za WE PROMISE TO BEAT ANY ADVERTISED PRICE OR WRITTEN QUOTATION ON SIMILAR QUALITY PRODUCTS. sausage maker, sausage making machine, sausage filler, sausage casing, how to make sausage, sausage filler for sale, sausage stuffing, wors making machine, beef sausage recipes, boerewors making machine for sale, sausage machine, wors machine for sale, sausage maker price, boerewors making machine, mincer and sausage maker, industrial sausage making machine, sausage maker for sale, sausage stopper, wors machine, sausage machine for sale, electric sausage filler, vertical sausage filler, sausage suffer, sausage stuffer price, industrial sausage filler, sausage filling machine, sausage making equipment Items Available: 5

V-Smart Series Contour Cutting Vinyl Cutter 1310mm Working Area with Stand, plus FlexiSIGN Software (NEW) SKU:V3-1313 - R14999 0724055174 http://am.co.za/plotter/contour # We provide great support on our machines include remote assistance direct to your computer, Free technician and will not charge you labour for the lifetime of the product. High-end protocol chip set supports all Windows System, Mac OS & Linux computer connectivity; LCD touch screen makes it easy to operate; Direct read files on USB Drive for cutting. 4M built in memory to store digital designs; For precision outline cut Laser Optical Sensor tech is used; 32bit central processing unit with very fast high speed 4M cache; You can browse through our large selection of products on this website: http://am.co.za/plotter/contour # We are sure that you will find the right kind of products for your task. Have an inquiry, feel free to contact me on 0724055174 Our Contour Cutter Vinyl Cutter is a All-in-One pre-printed media cutting solution. Easily the best contour cutter we have used. Period. Are you searching for a vinyl cutter to cut printed media, stickers, decals, heat transfer vinyl or digital designs? Our Contour Cutting Vinyl Cutter is what you are looking for, this is a superb automatic contour cut equipment with PC and USB flash drive connectivity. For further information, you can browse to: http://am.co.za/plotter/contour # Or call me at 0724055174. Our customer care executives are always happy to aid you with all your queries and concerns. The Outline Cut Vinyl Cutting machine supports all of the best operating systems. That means Windows XP/Vista/7/8, Apply Mac OS, and Linux. How Contour Cutting Works Cut any sticker with our Contour Cutting Vinyl Cutter is very easy and requires only a few steps. You simply need the artwork (.PLT file, output by many vector designer e.g. CorelDRAW) and our Contour Cutter will cut your sticker automatically. You can connect it via PC to feed the design or you can use USB flash drive to work on any Plotter file. If you would like additional information prior to deciding, don't wait to call me on 0724055174. I will answer your queries and put all your worries to rest. For more information please check our website at: http://am.co.za/plotter/contour # and browse through it to find out more about our products and services. Advanced Machinery is making machines at "made in China" prices locally here by working with machine factories and setting up assemble-lines in Johannesburg. At last, you still get the super affordable price of equipments made in China plus great service and the after-sale support you deserve. Please visit our website: http://am.co.za/ # for Wood Router, Paper Cutter, Laser Cutter, Hypertherm Plasma and many more.

Technical Specification 1. Type and Specification: 820 Glazed Tile Roll Forming Machine 2. Technique parameters of the processing line (1)Suitable material: Color steel (2)Thickness of the plate: 0.3-0.8mm (3) Input width of the plate: 1000mm (4)Width of the plate after forming: 820mm (5) Productivity: 2-4m/min (6) Roller steps: 12 rows (7) Roller material: 45# steel rolling chrmium thickness: 0.05 mm (8) Diameter of active shaft: 80mm (9) Wall thickness of the main forming machine: 14mm steel plate (10)Main forming machine body: 350mmh steel (11)Transmission chain is 0.6'' Reducer is 5.5kw which works stably and no noise. Ms.Bella Sales Manager _ _ _ Cangzhou All Service Machinery Equipment Co., Ltd Tel:0086-317-8201018 Mobile:+8615716869598 Email:allservice5@163.com Skype:bella201324

Manhattan Corporation, currently in its 26th year of operation, provides BEST VALUE Turnkey Mining and Process Solutions to the mining and minerals processing industry. Its focus is on Best Value encompassing, well priced solutions from Feasibility, Design, Manufacturing, Equipment Supply, Installation, Commission and Implementation.

Industry Applications LF3015GA fiber laser cutting machine can carry up to 8000W laser power, so cutting some thick plate, it is a very good choice. For example, agricultural machinery, textile machinery, food machinery and construction machinery and other large machinery and equipment manufacturing, usually use high power fiber laser cutting machine for processing.  Suitable for stainless steel, carbon steel, silicon steel, aluminum alloy, titanium alloy, galvanized steel, aluminum-plating zinc plate, copper, and other metals. if you need more information please just contact with me Etienne Kalp www.featureequipment.co.za http://shalommachines.business.site/ https://etiennekalp.wixsite.com/shalommachines 081 513 2491 Items Available: 1 Stock ID: ekL Fiber 1 YEAR WARRANTY ON ALL MACHINES Free training (T's and C's Apply) Free Installation (T's and C's Apply)

Intermediate Life Support (ILS) The position of for an ILS has become available at a Renowned Company in Port Elizabeth. Purpose of Position: To provide specialized pre-hospital health care to injured, sick, infirm, and aged persons and emergency transport to medical facilities at ILS level of care when required. Requirements: Current registration with HPCSA as ILS. Must have a valid Code 8 or 10 driver’s license, and Prdp, non-negotiable. Certificate in Intermediate Life Support Matric with Math’s and Science Minimum of one years’ experience post qualification. Ability to work effectively in a team. Ability to perform and remain calm under high pressure situations. Excellent telephonic/radio communication skills. Excellent communication skills with colleagues, hospital staff and Doctors. Fluent in English. Any additional languages will be advantageous. Flexibility to adapt and cope with changes at short notice. Strong administration skills with attention to detail. Must be PC literate – basic word, excel and e-mail Responsibility: Key Performance Areas: Safe patient care in compliance within HPCSA protocols as an ILS. Efficient handling of and response to emergency calls as per company policy. Accurate completion and administration of all required patient and company documentation. Responding timeously to all call outs. Assessing health status of persons involved in accidents, natural disasters and other emergency situations. Monitoring changes in the health status of patients during transport to and from medical, rehabilitation and other health care facilities. Performing medical procedures/treatment at ILS level of training, Efficient and effective management of emergency medical and trauma calls as per company standards, policies, and procedures. Recording information on patient’s conditions and treatment on Patient Report Form (PRF) in accordance with guidelines published by HPCSA. Accurate completion of PRF’s and submission for processing according to scheme and company policy. Responsible driving of emergency vehicles in accordance with company policy and National Road Traffic Act Safe operating of company vehicles and equipment as per company policies and procedures. Practice of strict infection control measures and maintaining a safe, healthy, and accident-free workplace. Active participation in continuous development activities aimed at improving and updating clinical and industry related knowledge. Compliance with Continuous Professional Development (CPD) guidelines published by HPCSA. Be able to inspire, motivate, develop, and lead other staff to ensure efficient clinical and professional emergency medical care. Salary is market related Send CV to info@performitpersonnel.co.za Salary: Rnegotiable Job Reference #: ILS001 Consultant Name: Damian Sin Hidge

Managing all aspects of the forecourt, incl. cash-ups and daily banking • Managing forecourt staff, incl. arranging of shifts and maintaining staff discipline • Ensuring all forecourt equipment is maintained • Professional handling of all customer queries/complaints • Ordering, receiving, processing and merchandising of stock • Relaying of fuel readings to suppliers • Cost control and administrative duties Must have HR experience Minimum Requirements • Min Grade 12 • Computer Literate and fluent in MS Office • Excellent administrative skills • Experience in people management • Strong interpersonal skills • High level of motivation, initiative and integrity • Previous Forecourt supervisory/admin experience advantageous Email cv to pietert777@gmail

Overview The all-digital non-touching infrared automatic cut-to-length system developed by Wuhan CenterRise M&C Engineering Co., Ltd. is the first digital measurement, digital transmission, digital positioning and digital control technology in China. It is suitable for the primary and secondary cutting of continuously cast product of square billets, rectangular billets, slabs, round billets and shaped billets. It can automatically cut 1-24 strands billets to length at the same time, and display the casting speed and running status of each billet. The system has high measurement and control accuracy and strong anti-interference ability, which improves the output and quality of the cast products and reduces the labor intensity of the operator. The whole system has the advantages of low investment, simple installation, debugging and operation, and basically maintenance free. No need to change the original production equipment, a major breakthrough in the automatic cut-to-length cutting method, and it is also an important part of the continuous casting process, which has been highly praised by experts and manufacturers. Digital infrared cutting to length can also provide high-definition solutions, so that the measurement error is ±2mm, and the system can support 4 strands high-definition CCD image measurement. The features of the system 1. The system adopts advanced digital image processing technology (non-touching type) to identify the length of hot billet online, automatically controls the flame cutting machine to cut the hot billet to a certain length, detects and displays the running status and casting speed, and collects the image information of the moving billet from a long distance through an infrared camera. 2. The computer processes the image information by pattern recognition program, forms the operation information and converts it into the electrical signal of the specified format, so that the hot billet can be cut by the actuator. The system can cut the 1-24 strands to length at the same time with an infrared camera. 3. A schematic diagram of the overall layout and working principle of the system is shown in Figure 1. Fig 1 The functions of the system 1. Applicable to all kinds of continuous casting machine flame cutting system. 2. Adopt advanced digital image pickup technology. 3. It is not sensitive to other high-intensity light interference, and overcomes the influence of light sources such as sunlight and arc welding. 4. The system provides abundant interfaces, which can communicate with with the PLC. 5. The fixed-length parameters and data can be directly modified by the secondary system to optimize the fixed-length cutting. 6. Historical cutting data is automatically stored, and the system can set rules for historical data. 7. Support the free transformation of fixed length, and a variety of operation modes are available for the operator to choose. 8. Each stream can send out signals such as pre-clamping, clamping, cutting, roll-up, roll-down and return of the cutting car according to the user's requirements. 9. The monitor displays the running status of the current hot billet in real time and displays the corresponding parameters. 10. Data management can be carried out according to shifts, pouring times, days, weeks, months, etc., as well as data management according to specifications, production capacity, quality, etc. 11. Provide automatic, manual cutting control. 12. The detection and cutting precision is high, and the controllable precision is ±5mm. The extension of the system The system can install 1 to 8 cameras. Generally, when one camera cannot meet the requirements, the system can be equipped with 2 to 8 cameras. The camera can be fixed inside and outside the operating room perpendicular to the roller line, and the setting height is generally 3-5 meters, so that the camera can clearly and completely capture the image of the moving billet. High-definition line scan cameras can also be provided to perform high-precision positioning of each strand of cast products. Line scan cameras are used to support up to 12 strand systems, which ensures that the center of the viewing angle, the billet head, and the fixed-length mark are vertical to improve the cutting and fixed-length accuracy. The technical parameters 1.Numbers of caster stands: maximum 24 strands 2.Cutting method: flame cutting 3.Matching casting speed: ≤6.5m/s 4.Temperature range of billets: 1000℃ 5.Measurement accuracy: ±5mm 6.Cut-to-length range: 3-18m 7.Signal transmission: TCP/IP 8.Number of signals: pre-cut, cut

Overview LGK-JS03 Mould Breakout Prediction System Thermocouple Calibrator is a patented product of Wuhan CenterRise M&C Engineering Co., Ltd. It is a special equipment specially developed for off-line detection of mold breakout prediction thermocouples. This calibrator has the advantages of high test accuracy, reliable data, light weight, portable and easy to use. It can fully meet the needs of on-site installation testing and use process verification. It is an essential tool for on-site online testing. The detection principle In the process and normal production of mold thermocouple offline installation in mold breakout prediction system, LGK-JS03 mould breakout prediction system thermocouple calibrator is an automatic special instrument for thermocouple detection. The system simultaneously measures the wide surface inner arc, wide surface outer arc and narrow surface of the mold through a special embedded signal processing system. The 128 thermocouple sensors can be scanned on one side at most, and the current thermocouple status is displayed in real time on the LCD panel of the calibrator. The function of the system 1. Using digital dynamic measurement technology, it can measure up to 8x16 thermocouple arrays’ temperature at the same time 2. Realize full digital measurement 3. The system realizes automatic temperature compensation and automatic recording 4. Multiple modes of display output, providing a rich and complete human-machine interface 5. Provide single-point, cycle, multi-point display, and provide temperature rise detection and galvanic couple state judgment 6. On-line identification and diagnosis function, providing broken couple, short circuit and alarm functions 7. Can adapt to all breakout forecasting systems on the market 8. Support temperature field and temperature array detection at the same time 9. With print and storage function The features of the system 1. Humanized human-computer interface 2. Multiple display modes 3. Convenient system settings 4. With historical data storage and printing functions 5. The system connection has a wide range of adaptability and supports the connection interface of all mold breakout prediction and detection systems in the market. 6. Specially designed heating system 7. Portable (built-in rechargeable battery) The performance index The measuring range The optional parameters: -100℃-0℃; -100℃-100℃; -100℃-200℃; 0℃-100℃; 0℃-200℃; 0℃-500℃; 0℃-800℃; 0°C-1000°C; 100°C-200°C; 100°C-500°C; 200°C-1000°C; 500℃-1000℃, 12 parameters in total. The default parameter is the measurement range of 0℃-200℃. Adaptable sensor: J-type, K-type, T-type thermocouple The detection accuracy t99.9℃ (±0.25% of reading) t999℃ (±0.2% of reading) The detection range Type J: -100℃-1000℃ Type K: -100℃-1000℃ Type T: -100℃-400℃ Working temperature: -10℃~60℃ Battery level indicator: support Instrument size: 840x160x320cm Instrument weight: 3700g

We specialize in providing a Business / System Analysis service with the associated custom software written to suit your business requirements. We assist businesses and individuals to improve their business processes through data modelling and database management. We make use of sophisticated and customizable SQL database solutions and MS Access to suit your own requirements. Our system offers a dynamic approach to software development. Our software is a user-customizable application that allows users to create their own software modules on the fly. Our software is unique in that it allows its users to build additional functionality within the software completely, without programmer intervention. Modules can be added to the system which supports hierarchical data structures, with customizable fields for each module created. The system is an effective Interactive Database Data Management System that has been designed to allow setups to suit user requirements from all industries. Our system program is also particularly useful to freelance consultants, freelance programmers or system developers to use as their preferred database system platform for their own clients. The development time for programmers and developers is substantially less than other conventional system platforms available. The process of database design has been simplified to the extent that users proficient in Microsoft Excel can easily convert a spreadsheet application into our database application type. Programming is simple as it mirrors much of Microsoft Excel and Microsoft Access functionality. Advanced Crystal Report writing, VB.Net, VB Visual Basic, VBA, C Sharp or C++ functions can also be integrated into the system. The system platform offers a combination of the functionality of a database program together with spreadsheet, word processing, documentation control functionality and Microsoft Project-style gantt chart planning. Multiple databases can be combined into one application using the system platform. The system platform supports various methods to populate a database including a direct interface, a webpage interface, a tablet interface or through an Excel or Word interface. The system can be setup to run on a stand alone computer or on a network. We currently have applications setup on the system that include: Construction Management Document control and Document Management Marketing Management Tender Management and Construction Cost Estimating Contract Management Subcontract Management Correspondence Management Programming and Planning Management Risk Management Health and Safety Management Quality Assurance Environmental Management Human Resources Management Internal Plant Management Stores Management Wage Personnel Management Salary Personnel Management Labour Costing Goods Received Costing Hired Plant and Equipment Costing Overheads Costing Subcontractor Costing Head Office Costing Accounting Cost and Management Performance Reporting Our skill sets include: Dynamic SQL / T-SQL SQL Server Database Administration, Reporting, Integration, Management, Database Building, SQL Store Procedures C#, VB.Net, VBA, HTML, AjaxControlToolkit, Javascript Crystal Report Writing Web interfaces to integrate data to databases Tablet Interfaces to integrate data to databases Windows server management Network setup and secity Microsoft Visual Studio Kaspersky security management Infragistic controls