Pool seal mechanical

Buy Quality pool pump Shaft seal | Mechanical seal for 0.45kW, 0.6kW, 0.75kW, 1.1kW, 1.5kW (S... - 0.6kW for R212.00

Buy Quality pool pump Shaft seal | Mechanical seal for 0.45kW, 0.6kW, 0.75kW, 1.1kW, 1.5kW (S... - 1.5kW for R351.00

Buy Quality pool pump Shaft seal | Mechanical seal for 0.45kW, 0.6kW, 0.75kW, 1.1kW, 1.5kW (... - 0.45kW for R222.00

Buy Quality pool pump Shaft seal | Mechanical seal for 0.45kW, 0.6kW, 0.75kW, 1.1kW,... - 0.55kW / 0.6kW for R244.00

Buy POOL LIGHT HOUSING WITH GLAND NUT AND SEAL 170mm for R299.99

Buy Quality/Eartheco- Replacement Mechanical (Shaft) Seal Kit for 0.45-1.1kw for R219.00

Fibreglass Relinings/Resurfacing (Western Cape). FIBREGLASS RE-LININGS, RESURFACING, NEW LININGS FOR SWIMMING POOLS, POOL RESURFACING, POOL REPAIRS, POOL PLASTER, MARBELITE, FIBREGLASS, FIBER LINING, FIBRE LINING, FIBRE GLASS, NEW LINING, •Friendly Pools only uses SABS approved fibreglass and resin to reline swimming pools. The fibreglass and resin is suitable for concrete and marbalite pools. The surface of the pool must be clean from any debris and dust so that the fibreglass lining can stick to the surface. A groove is cut underneath the coping/paving so that the fibreglass can be tucked in. A layer of resin is applied and then a 450gramm fibreglass matt. Another layer of resin is applied on top of the fibreglass matt. The fibreglass underneath the coping/paving is then sealed with a bonding paste. Fibre mosaics is then applied and sealed with clear topcoat. The surface is then smoothed out before the pool coat is applied. The pool must stay empty for at least 4-6 days for the wax in the poolcoat to seal.

IDQB40 Peripheral Vane Water Pump with Pressure Switch Volumetric water pumps able to offer high pressures in relation to relatively low power. The IDQB pump is used in domestic applications to increase the system pressure. For the correct functioning of the pumps use clean water, non-aggressive liquids only, without sand of other solid impurities. Operating limits: * Suction lift up to 6-8m with foot valve * Maximum operating pressure: 8 bar * Maximum ambient pressure: +40°C * Liquid Temperature up to +90°C Design features: * Pump body/motor support: cast iron * Impeller: brass * Motor shaft: AISI1045 * Mechanical seal: NBR/Graphite/Ceramic SKU: 15220 Contact: Phone/Whatsapp: 062 857 9004 or email: bsapotchefstroom@gmail.com

IDQB40 Peripheral Vane Water Pump with Pressure Switch Volumetric water pumps able to offer high pressures in relation to relatively low power. The IDQB pump is used in domestic applications to increase the system pressure. For the correct functioning of the pumps use clean water, non-aggressive liquids only, without sand of other solid impurities. Operating limits: * Suction lift up to 6-8m with foot valve * Maximum operating pressure: 8 bar * Maximum ambient pressure: +40°C * Liquid Temperature up to +90°C Design features: * Pump body/motor support: cast iron * Impeller: brass * Motor shaft: AISI1045 * Mechanical seal: NBR/Graphite/Ceramic SKU: 15220 Contact Us on 061 935 3537 or email: bsajohannesburg@gmail.com

Kelvinator Bar Fridge (120L) ENERGY EFFICIENCY: A + CONSUMPTION: 110 KWH / YEAR DIMENSIONS: HEIGHT: 840mm WIDTH: 480mm DEPTH: 430mm FEATURES AND SPECIFICATIONS: • ADJUSTABLE THERMOSTAT WITH MECHANICAL CONTROL • REVERSIBLE DOOR • ANTI BACTERIAL DOOR SEAL • SPILL PROOF SAFETY GLASS • ADJUSTABLE LEVELING FEET • FLUSH BACK DESIGN • SEPARATE ICE COMPARTMENT • INTEGRATED HANDLE Low noise, perfect working condition, no longer needed as I've upgraded to a bigger fridge. The brand speaks for itself. Currently plugged it for buyer to inspect prior to buying. Whatsapp preferred.

Application Limits of Vertical Pump Medium temperature: normal type: 0℃~68℃ hot water type: 0℃~120℃ Ambient temperature: +40℃ Max ambient pressure: 1.0MPa Advisable to use a motor of a higher power in case that the density or viscosity of the medium is above that of water. Selection of Pumps Selection of pumps should be based on: Duty point of the pump Dimensional data such as pressure loss as a result of height differences, friction loss in the pipework Pump efficiency Pump materials Pump connections Commonly used mechanical seal configuration tables 1. Duty point of the Pump From a duty point, it is possible to select a pump on the basis of the curve charts shown in “performance curves/technical” data. 2. Dimensional Data When sizing a pump the following must be taken into account: Required flow and pressure at the draw-off point. Pressure loss as a result of height differences. Friction loss in the pipework (Hf) (Refer to Fig.1) it may. Highest efficiency at the estimated duty point. NPSH value. For calculation of the NPSH value, see the corresponding curves chart. 3. Pump Efficiency Before determining the best efficiency point, the operation pattern of the pump needs to be identified. If the pump expected to operate as the same duty point, then select a BL pump which is operating at a duty point corresponding with the best efficiency of the pump. As the pump is sized on the basis of the highest possible flow, it is important always to have the duty point to the right on the efficiency curve (eta) in order to keep efficiency high when the flow drops.

QB-Self Priming Pressure Pump Motor · 2 pole induction motor. · Single phase 220V, 50/60Hz. · Insulation: Class B/Class F. · Protection: IP44. · With capacitor and thermal overload protector. QB-Self Priming Pressure Pump Material · Pump body: Cast Iron. · Motor support: Aluminum. · Impeller: Brass. · Motor shaft: Stainless Steel or CS45#. · Mechanical seal: Ceramic-Graphite. · 100% copper winding. Operating Conditions · Suction lift up to 8m. · Liquid temperature up to +40℃. · Ambient temperature up to +40℃. · Max. working pressure: 6 bar.

Seakoo QB60L Self-Priming Peripheral Pump + Controller · 2 pole induction motor. · Single phase 220V, 50/60Hz. · Insulation: Class B/Class F. · Protection: IP44. · With capacitor and thermal overload protector. QB-Self Priming Pressure Pump Material · Pump body: Cast Iron. · Motor support: Aluminum. · Impeller: Brass. · Motor shaft: Stainless Steel or CS45#. · Mechanical seal: Ceramic-Graphite. · 100% copper winding. Operating Conditions · Suction lift up to 8m. · Liquid temperature up to +40℃. · Ambient temperature up to +40℃. · Max. working pressure: 6 bar

Centrifugal Pump Motor ◆ 2 pole induction motor. ◆Single phase 220V, 50/60Hz; Three phase 380V, 50/60Hz. ◆Insulation: Class B/Class F. ◆Protection:IP44. ◆With capacitor and thermal overload protector. Centrifugal Pump Material ◆ Pump body: Cast Iron. ◆ Motor support: Aluminum. ◆ Impeller: Brass. ◆ Motor shaft: Stainless Steel or CS45#. ◆ Mechanical seal: Ceramic-Graphite. ◆ 100% copper winding. Centrifugal Pump Operating Conditions ◆ Suction lift up to 7m. ◆ Liquid temperature up to +40℃. ◆ Ambient temperature up to +40℃. ◆ Max. working pressure: 6bar.

Application Limits Suction head up to 7m Liquid temperature up to +40℃ Ambient temperature up to +40℃ Max. Working pressure: 6bar Voltage fluctuation should not exceed 10% of rated value. pH: 6.5 to 8.5 Applications Fields Suitable for transferring water without abrasive particles or other liquid whose properties are similar to water. Widely used in vegetable greenhouse water supply, breeding industry water supply and drainage, water tower water supply, pipeline pressurization, various corollary equipment, etc. Features Single suction centrifugal pump, with high efficiency Copper impeller, stable performance High head, small flow rate Motor Single-Phase 220V/50Hz Mechanical seal: Ceramic/Graphite/NBR rubber Motor: 2 pole asynchronous motor, copper wires, built-in thermal protector, fully closed fan cooling, continuous running Protection: IP44 Insulation: Class B