Light industrial storage unit

Overview The continuous casting vibration type ladle slag detection device is used to detect the slag content of the ladle nozzle in the steelmaking continuous casting process, so as to improve the cleanliness of the tundish molten steel and obtain the best yield of the ladle molten steel. The device adopts the principle of vibration detection. The LAG-S200 continuous casting ladle slag automatic detection system is developed by Wuhan CenterRise M&C Engineering Co., Ltd. after many years of research with many scientific research institutes, and fully combined with the actual situation on site. It has a real field application value as a continuous casting ladle slag automatic detection system. The meaning of the system 1. Reduce the amount of tundish slag 2. Improve the purity of molten steel 3. Improve the life of the tundish 4. Reduce sliding nozzle erosion 5. Reduce nozzle blockage 6. Increase continuous pouring heats 7. Reduce the amount of residual steel in the ladle when high-quality steel is casting 8. Improve the yield of molten steel 9. Improve the quality of continuous casting billets In order to improve the purity of the molten steel in the tundish, and improve the quality of the casting billet, especially to improve the quality of the billet in the transition section, and reduce the amount of residual steel in the high-quality ladle, and prolong the life of the tundish lining, and increase the continuous casting heats, it’s necessary to detect and control the slag in the later stage of continuous casting ladle casting. The working principle The LAG-S200 continuous casting ladle slag automatic monitoring system detects the slag state during the pouring process by receiving the vibration signal of the mechanical operating arm of the ladle nozzle. In the process of molten steel pouring, when molten steel flows through the long nozzle and pours into the tundish, the molten steel impacts the wall of the long nozzle and causes the vibration of the mechanical operating arm used to support the long nozzle. Since the specific gravity of the steelmaking slag is less than half of the specific gravity of the molten steel, it floats on the surface of the molten steel, and the steelmaking slag appears when the molten steel is about to be all poured. At this time, due to the high viscosity and poor fluidity of light steelmaking slag, the impact force of the mixed flow of molten steel and steel slag on the wall of the long nozzle is quite different from that of pure molten steel. The system mainly monitors the ladle slag of the continuous casting by measuring and analyzing the vibration difference of the mechanical operating arm. The vibration signal is connected to the operation control unit of the system control cabinet through the front-stage conditioning and amplification module through the sensor installed in the middle of the operating rod. After processing, it is output to the industrial computer for operation and analysis. The slag signal detected by the system is output from the system control cabinet to the front-end control unit, and then control the alarm horn and alarm light to work, or issue an instruction to close the ladle nozzle. The features of the system (1) It is easy to install, basically no modification is made to the field equipment, and the installation and debugging work will not affect the normal production of the enterprise. (2) The detection accuracy is high, and the effective rate is greater than or equal to 95%. The threshold of slag volume is accurately set, the output control function is powerful. It has excellent performance in technical indicators such as the sensor service life and sensor usage times. (3) The sensor is installed at a position far away from the molten steel, and is cooled by a special refrigeration device for 24 hours. The outer layer adopts a composite protection structure, which has a long service life. (4) Adopt professional and targeted signal processing methods to obtain the vibration characteristic parameters of the ladle slag, and analyze, reason and judge the effective slag signal through the vibration signal database, which has a high accuracy of slag alarm. (5) The architecture is established based on the artificial intelligence network, which has the functions of self-learning and self-induction. (6) The equipment adopts a modular design. The failure of each module will not affect other parts, which ensure more reliable operation of the system and easy maintenance. (7) The alarm display device is used on site to visually indicate the flow state of molten steel and slag. When slag carryover strats, we can choose automatic mode or manual mode. In both modes, the system will give audible and visual alarm signals to remind on-site operators. (8) The system has a powerful database function. Including the comparison function for last two ladles of casting time record, the system automatically stores the running data, and generates a record file every day. (9) The system has the function of automatically controlling the ladle nozzle. The control unit is an auxiliary system of the system, which is interconnected with the ladle slag detection system to automatically control the opening of the ladle nozzle and realize the whole-process control of the liquid level of the molten steel in the tundish. The composition of the system The LAG-S200 slag detection system consists of: vibration detection sensor, pre-signal amplifier, slag detection operation unit, tundish liquid level control unit, on-site operation indication box, and process control cabinet. 1. Vibration detection sensor: It is installed on the robotic arm of the stopper to detect the vibration signal of the whole casting process of the ladle. 2. Pre-signal amplifier: Amplify, convert and transmit the weak vibration signal detected by the vibration detection sensor. 3. Slag detection operation unit: Analyze, judge and discriminate the vibration signal to realize the discrimination of all steel, mixed slag and full slag , and output the slag alarm signal. 4. Tundish liquid level control unit: Accept the control signal of the tundish nozzle and the ladle nozzle, and realize automatic or manual control to the ladle slag according to the requirements. 5. On-site operation instruction box: Provides man-machine exchange for slag alarm indication, fault indication, system activation mode selection, and control mode selection. 6. Process control cabinet, providing power management, displaying man-machine interface and setting management. The parameters of the system 1. The system controls the slag inclusion in molten steel with high precision and closes the nozzle in real time. 2. Improve the quality of steel, reduce defective products, and improve the yield. 3. The yield of molten steel is increased by 0.3%-0.5%. The nozzle can be automatically closed, so that the disadvantage of untimely manual response is overcome and less molten steel remains in the ladle. The threshold value of molten steel (slag threshold) is set by the user within a wide range. 4. No artificial factors are involved, high reliability, good repeatability or consistency. 5. The steelmaking slag does not pass through or rarely flows into the tundish, which increases the service life of the refractory material and the sliding nozzle. 6. Reduce the blockage of the tundish nozzle and increase the number of continuous pouring heats of the tundish.

Overview： This product is a new type of mold copper plate surface cladding detection equipment. The equipment adopts a high-precision and high-sensitivity laser ranging sensor, which scans the copper plate of the mould by scanning a laser line with a fixed width, and returns the measurement data in real time. After modeling and analyzing the data, the upper computer gives the wear data of the mold copper plate, as well as the data of surface cracks and surface roughness. The host computer software intuitively reflects the surface profile of the detected mold and cladding thickness deviation and other data to the user in the form of data sheet, data curves and mold 3D model diagrams, providing a true and reliable theory for on-site operators to maintain the mold. The mold surface cladding detection equipment is a high-precision instrument, which includes high-precision laser ranging sensors, two digital servomotors, encoders, horizontal sliding screws, vertical sliding screws, and calibration consoles, controllers and other components. The equipment has many advantages such as high accuracy, strong stability, convenient installation and strong observability. It is suitable for mold surface cladding detection, surface flatness analysis, surface flaw detection, taper measurement, etc. It is also suitable for round billets, square billets, slabs, special-shaped billets, etc., widely used and powerful. The composition of the system： 1. The mold surface cladding detection equipment is equipped with: data processing and display unit, horizontal motion mechanical power output unit, vertical mechanical power output unit, instrument motion control unit, laser measurement sensor, and instrument bracket. 2. Data processing and display unit: used for data acquisition and storage, system equipment control, parameter configuration, height display of the descent, start and stop control, etc. 3. Horizontal motion mechanical power output unit: the digital servo motor in the horizontal direction controls the sensor to move in the horizontal direction, so that the sensor can scan the horizontal inner cavity wall of the mold copper plate to detect data. 4. Vertical mechanical power output unit: the digital servo motor in the vertical direction controls the sensor to move in the vertical direction, so that the sensor can scan the vertical cavity wall of the mold copper plate to detect data. 5. Instrument motion control unit: It is used to control the motion scanning of the motor, and the running speed, running track, and control mode of the motor can be configured through parameter settings. 6. Laser measurement sensor: The laser displacement sensor adopts the principle of laser triangulation. The laser transmitter shoots the visible infrared laser to the surface of the measured object through the lens, and the laser reflected by the object passes through the receiver lens and is received by the internal line array image processing sensor. According to different distances, the corresponding positions of the light spots received on the line array sensor are also different. According to the angle of this reflection, the distance between the actual objects can be calculated by calculating the distance of the sensor spot. 7. Instrument bracket: The mold surface cladding detection equipment need to be placed directly above the mold when it is in use, and it is required to be fixed firmly without displacement vibration during the measurement process to ensure the measurement accuracy. The parameters： Detection instrument service life: ≥5 years; Detection instrument reliability: more than 98%; Detection range: 60~1000mm (customizable) Detection accuracy: 0.01mm Spot diameter: 1.0x1.5mm (spot scan), 1.0x20mm (line scan) Falling pace: 1~20mm/step Single measurement time: less than 2min Power supply: DC24V Operating temperature: -20~80℃ Equipment warm-up time: 3~5min Shock resistance: 50G (X, Y, Z axis) Vibration resistance: 10Hz~5Hz (amplitude 1.5mm, each 2 hours in X, Y, Z axis)

EasyRoute 380V Standard 2050x4000mm Hard PVC/Bakelite Clampable Vacuum CNC Router, 5kW Water-Cooled Spindle & Stepper Motors,, Vacuum Pump & Dust Collector Full Package R-2040V/50 CNC Router EasyRoute 380V Standard 2050x4000mm Hard PVC/Bakelite Clampable Vacuum CNC.... SKU: R-2040V/50 from AM.CO.ZA CNC Router Price: R326159 excl. valid at 2022-02-23 http://saleprice.co.za/R-2040V/50# Machines / CNC Routers https://buythis.co.za/cnc-routers# CNC Router HE3ADSYS/AMCOZA/R-2040V/50 --- Achieve Under 0.5mm Per Meter Accuracy & Repeatability on All Axis With 100mm Diamter 5kW Water-Cooled Spindle on 7.5kW Inverter (Allow Upgrade to Bigger Spindle) for Maximum 24000RPM, ER20 Collet Size Clampable Vacuum Table Surface Made By Bakelite or Hard Rigid PVC, Very Durable & High Wear-Resistant, Several Aluminium Clamping T-Slots Build In With Standalone EasyRoute Control System, No Computer Needed, Stable System Suitable for Industrial Usage DSP Controller use ARM Cortex-A8 800MHz CPU, 512MB Internal Cache & 512MB Flush Memory for Storage Use Industrial 380V 3-Phase Electricity, 5 Pin 32A Plug, 4mm Cable Required & Not Included Linear Guide Rail in Twin Parallels Structure & Two Roller Bearing Sliders on Each Rail Guide X/Y/Z Movement High-Load, High-Speed Caged Ball Screw Transmission System on Z Axis 5.5kW 380V Motor, RPM 1440 for Liquid Ring Vacuum Pump, Provide 0.097 MPa Vacuum Level on 8.3 L/min Fluid Flow Rate & 3.83 M 3 /min Air Flow Rate. Just Very Noisy 68dB. High Precision Rack & Pinion System, Helical Teeth Driving System on X & Y Axis Rugged Keypad Against Water, Oil, Dust & Collision, Cheap & Easy to Replace If Damaged Z-Axis Setter/Presetter Included, Automatic Measure Tool Length & Establish 0 Reference Point Working Area 2050x4000x300mm on X/Y/Z, the Area Spindle Can Reach Accept All Kinds of G-Code File (*.g *.nc *.ug;*.demo;*.iso;*.eng;*.cut;*.dxf;*.plt;*.txt) by USB Flush Drive, G-Code File Size Up to 256M With Rotary Attachment Supporting Interface & can Switch between Rotary Rotating & X-Axis Linear Movement Total Four Stepper Motors on All Axis, Two Stepper Motors on Y-Axis Achieve 0.01mm Resolution on All Axis Maximum 20 Meter Per Minute Moving Speed on X/Y Axis,, Factory Default on 12 Meters/Min Maximum 5 Meter Per Minute Moving Speed on Z Axis,, Factory Default on 3 Meters/Min --- R-2040V/50: EasyRoute 380V Standard 2050x4000mm Hard PVC/Bakelite Clampable Vacuum CNC Router, 5kW Water-Cooled Spindle & Stepper Motors,, Vacuum Pump & Dust Collector Full Package Price: R326159 excl. WhatsApp 0606006000 / 0722222211 Call 01139... Stock Code: am-r-2040v-50 Items Available: 1 Stock ID: am-r-2040v-50 Send WhatsApp to 0606006000 Johannesburg Branch: Unit 7 Burns Business Park, 12A Jet Park Road, Jet Park 087 802 5368 / 011 397 1429 Cape Town Branch: Unit 6 Alternator Park, 7 Alternator Ave, Montague Gardens 087 802 7106 / 021 555 3250

EasyRoute 380V Standard 1300x2500mm Hard PVC/Bakelite Clampable Vacuum CNC Router, 5kW Water-Cooled Spindle & Stepper Motors,, Vacuum Pump & Dust Collector Full Package R-1325V/50 CNC Router EasyRoute 380V Standard 1300x2500mm Hard PVC/Bakelite Clampable Vacuum CNC.... SKU: R-1325V/50 from AM.CO.ZA CNC Router Price: R212699 excl. valid at 2022-03-14 http://saleprice.co.za/R-1325V/50# Machines / CNC Routers https://buythis.co.za/cnc-routers# CNC Router HE3ADSYS/AMCOZA/R-1325V/50 --- With 100mm Diamter 5kW Water-Cooled Spindle on 7.5kW Inverter (Allow Upgrade to Bigger Spindle) for Maximum 24000RPM, ER20 Collet Size Accept All Kinds of G-Code File (*.g *.nc *.ug;*.demo;*.iso;*.eng;*.cut;*.dxf;*.plt;*.txt) by USB Flush Drive, G-Code File Size Up to 256M Total Four Stepper Motors on All Axis, Two Stepper Motors on Y-Axis Maximum 5 Meter Per Minute Moving Speed on Z Axis,, Factory Default on 3 Meters/Min Working Area 1300x2500x300mm on X/Y/Z, the Area Spindle Can Reach Z-Axis Setter/Presetter Included, Automatic Measure Tool Length & Establish 0 Reference Point With Standalone EasyRoute Control System, No Computer Needed, Stable System Suitable for Industrial Usage With Rotary Attachment Supporting Interface & can Switch between Rotary Rotating & X-Axis Linear Movement Rugged Keypad Against Water, Oil, Dust & Collision, Cheap & Easy to Replace If Damaged Use Industrial 380V 3-Phase Electricity, 5 Pin 32A Plug, 4mm Cable Required & Not Included Maximum 20 Meter Per Minute Moving Speed on X/Y Axis,, Factory Default on 12 Meters/Min Linear Guide Rail in Twin Parallels Structure & Two Roller Bearing Sliders on Each Rail Guide X/Y/Z Movement Achieve 0.01mm Resolution on All Axis High-Load, High-Speed Caged Ball Screw Transmission System on Z Axis Clampable Vacuum Table Surface Made By Bakelite or Hard Rigid PVC, Very Durable & High Wear-Resistant, Several Aluminium Clamping T-Slots Build In DSP Controller use ARM Cortex-A8 800MHz CPU, 512MB Internal Cache & 512MB Flush Memory for Storage High Precision Rack & Pinion System, Helical Teeth Driving System on X & Y Axis Achieve Under 0.5mm Per Meter Accuracy & Repeatability on All Axis 5.5kW 380V Motor, RPM 1440 for Liquid Ring Vacuum Pump, Provide 0.097 MPa Vacuum Level on 8.3 L/min Fluid Flow Rate & 3.83 M 3 /min Air Flow Rate. Just Very Noisy 68dB. --- R-1325V/50: EasyRoute 380V Standard 1300x2500mm Hard PVC/Bakelite Clampable Vacuum CNC Router, 5kW Water-Cooled Spindle & Stepper Motors,, Vacuum Pump & Dust Collector Full Package Price: R212699 excl. WhatsApp 0606006000 / 0722222211 Call 0113971429... Stock Code: am-r-1325v-50 Items Available: 1 Stock ID: am-r-1325v-50 Send WhatsApp to 0606006000 Johannesburg Branch: Unit 7 Burns Business Park, 12A Jet Park Road, Jet Park 087 802 5368 / 011 397 1429 Cape Town Branch: Unit 6 Alternator Park, 7 Alternator Ave, Montague Gardens 087 802 7106 / 021 555 3250

EasyRoute 380V Standard 2050x3050mm Aluminium T-Slot Clamping CNC Router, 6.5kW High-Torque Water-Cooled Spindle & Stepper Motors R-2030C/65L CNC Router EasyRoute 380V Standard 2050x3050mm Aluminium T-Slot Clamping CNC Router,.... SKU: R-2030C/65L from AM.CO.ZA CNC Router Price: R239999 excl. valid at 2022-03-14 http://saleprice.co.za/R-2030C/65L# Machines / CNC Routers https://buythis.co.za/cnc-routers# CNC Router HE3ADSYS/AMCOZA/R-2030C/65L --- Water Chiller Maximum Pump Flow Rate 10L/min & Maximum Pump Lift 10 Metres Distance Use Industrial 380V 3-Phase Electricity, 5 Pin 32A Plug, 4mm Cable Required & Not Included Achieve Under 0.5mm Per Meter Accuracy & Repeatability on All Axis With 125mm Diamter 6.5kW High-Torque Water-Cooled Spindle on 7.5kW Inverter for Maximum 24000RPM, ER25 Collet Size Chiller Water Tank Capacity 9L, Purified Water Required (Not Supplied), Replace Monthly Suggested DSP Controller use ARM Cortex-A8 800MHz CPU, 512MB Internal Cache & 512MB Flush Memory for Storage Accept All Kinds of G-Code File (*.g *.nc *.ug;*.demo;*.iso;*.eng;*.cut;*.dxf;*.plt;*.txt) by USB Flush Drive, G-Code File Size Up to 256M Achieve 0.01mm Resolution on All Axis Linear Guide Rail in Twin Parallels Structure & Two Roller Bearing Sliders on Each Rail Guide X/Y/Z Movement High Precision Rack & Pinion System, Helical Teeth Driving System on X & Y Axis Z-Axis Setter/Presetter Included, Automatic Measure Tool Length & Establish 0 Reference Point With Rotary Attachment Supporting Interface & can Switch between Rotary Rotating & X-Axis Linear Movement Working Area 2050x3050x300mm on X/Y/Z, the Area Spindle Can Reach With Standalone EasyRoute Control System, No Computer Needed, Stable System Suitable for Industrial Usage Total Four Stepper Motors on All Axis, Two Stepper Motors on Y-Axis Maximum 20 Meter Per Minute Moving Speed on X/Y Axis,, Factory Default on 12 Meters/Min Working Area Specially Enlarged for South African Market that Offers 2050mm Width for Perspex High-Load, High-Speed Caged Ball Screw Transmission System on Z Axis Water-Cooled Chiller Radiating capacity 50W/ C, Energy Saving, Long Working Life Deisng Maximum 5 Meter Per Minute Moving Speed on Z Axis,, Factory Default on 3 Meters/Min Aluminium T-Slots Table Surface for Workpiece Clamping, 6 Clamps Included for Free Water-Cooled Chiller Uses Single Phase 220V Household Power, No AC Power Plug Included Rugged Keypad Against Water, Oil, Dust & Collision, Cheap & Easy to Replace If Damaged --- R-2030C/65L: EasyRoute 380V Standard 2050x3050mm Aluminium T-Slot Clampi... Stock Code: am-r-2030c-65l Items Available: 1 Stock ID: am-r-2030c-65l Send WhatsApp to 0606006000 Johannesburg Branch: Unit 7 Burns Business Park, 12A Jet Park Road, Jet Park 087 802 5368 / 011 397 1429 Cape Town Branch: Unit 6 Alternator Park, 7 Alternator Ave, Montague Gardens 087 802 7106 / 021 555 3250

EasyRoute 380V Standard 2050x4000mm PVC Clampable Vacuum CNC Router, 5.5kW High-Torque Water-Cooled Spindle & Stepper Motors,, 5.5kW Liquid Ring Vacuum Pump R-2040K/55V CNC Router EasyRoute 380V Standard 2050x4000mm PVC Clampable Vacuum CNC Router, 5.5kW... SKU: R-2040K/55V from AM.CO.ZA CNC Router Price: R286369 excl. valid at 2022-03-14 http://saleprice.co.za/R-2040K/55V# Machines / CNC Routers https://buythis.co.za/cnc-routers# CNC Router HE3ADSYS/AMCOZA/R-2040K/55V --- Linear Guide Rail in Twin Parallels Structure & Two Roller Bearing Sliders on Each Rail Guide X/Y/Z Movement With Rotary Attachment Supporting Interface & can Switch between Rotary Rotating & X-Axis Linear Movement High Precision Rack & Pinion System, Helical Teeth Driving System on X & Y Axis Accept All Kinds of G-Code File (*.g *.nc *.ug;*.demo;*.iso;*.eng;*.cut;*.dxf;*.plt;*.txt) by USB Flush Drive, G-Code File Size Up to 256M 5.5kW 380V Motor, RPM 1440 for Liquid Ring Vacuum Pump, Provide 0.097 MPa Vacuum Level on 8.3 L/min Fluid Flow Rate & 3.83 M 3 /min Air Flow Rate. Just Very Noisy 68dB. Achieve Under 0.5mm Per Meter Accuracy & Repeatability on All Axis Achieve 0.01mm Resolution on All Axis Water Chiller Maximum Pump Flow Rate 10L/min & Maximum Pump Lift 10 Metres Distance DSP Controller use ARM Cortex-A8 800MHz CPU, 512MB Internal Cache & 512MB Flush Memory for Storage Clampable Vacuum Table Surface Made By PVC, Aluminium Clamping T-Slots Build In With Standalone EasyRoute Control System, No Computer Needed, Stable System Suitable for Industrial Usage Maximum 20 Meter Per Minute Moving Speed on X/Y Axis,, Factory Default on 12 Meters/Min Chiller Water Tank Capacity 9L, Purified Water Required (Not Supplied), Replace Monthly Suggested Total Four Stepper Motors on All Axis, Two Stepper Motors on Y-Axis Maximum 5 Meter Per Minute Moving Speed on Z Axis,, Factory Default on 3 Meters/Min Water-Cooled Chiller Uses Single Phase 220V Household Power, No AC Power Plug Included Working Area 2050x4000x300mm on X/Y/Z, the Area Spindle Can Reach Use Industrial 380V 3-Phase Electricity, 5 Pin 32A Plug, 4mm Cable Required & Not Included High-Load, High-Speed Caged Ball Screw Transmission System on Z Axis Z-Axis Setter/Presetter Included, Automatic Measure Tool Length & Establish 0 Reference Point With 125mm Diamter 5.5kW High-Torque Water-Cooled Spindle on 7.5kW Inverter for Maximum 24000RPM, ER25 Collet Size Rugged Keypad Against Water, Oil, Dust & Collision, Cheap & Easy to Replace If Damaged Water-Cooled Chiller Radiating capacity 50W/ C, Energy Saving, Long Working Li... Stock Code: am-r-2040k-55v Items Available: 1 Stock ID: am-r-2040k-55v Send WhatsApp to 0606006000 Johannesburg Branch: Unit 7 Burns Business Park, 12A Jet Park Road, Jet Park 087 802 5368 / 011 397 1429 Cape Town Branch: Unit 6 Alternator Park, 7 Alternator Ave, Montague Gardens 087 802 7106 / 021 555 3250

EasyRoute 380V Standard 2050x3050mm Hard PVC/Bakelite Clampable Vacuum CNC Router, 5.5kW High-Torque Water-Cooled Spindle & Stepper Motors,, Vacuum Pump & Dust Collector Full Package R-2030V/55 CNC Router EasyRoute 380V Standard 2050x3050mm Hard PVC/Bakelite Clampable Vacuum CNC.... SKU: R-2030V/55 from AM.CO.ZA CNC Router Price: R293029 excl. valid at 2022-03-20 http://saleprice.co.za/R-2030V/55# Machines / CNC Routers https://buythis.co.za/cnc-routers# CNC Router HE3ADSYS/AMCOZA/R-2030V/55 --- DSP Controller use ARM Cortex-A8 800MHz CPU, 512MB Internal Cache & 512MB Flush Memory for Storage Achieve Under 0.5mm Per Meter Accuracy & Repeatability on All Axis Chiller Water Tank Capacity 9L, Purified Water Required (Not Supplied), Replace Monthly Suggested High Precision Rack & Pinion System, Helical Teeth Driving System on X & Y Axis Maximum 5 Meter Per Minute Moving Speed on Z Axis,, Factory Default on 3 Meters/Min Linear Guide Rail in Twin Parallels Structure & Two Roller Bearing Sliders on Each Rail Guide X/Y/Z Movement Water Chiller Maximum Pump Flow Rate 10L/min & Maximum Pump Lift 10 Metres Distance Use Industrial 380V 3-Phase Electricity, 5 Pin 32A Plug, 4mm Cable Required & Not Included With Rotary Attachment Supporting Interface & can Switch between Rotary Rotating & X-Axis Linear Movement With 125mm Diamter 5.5kW High-Torque Water-Cooled Spindle on 7.5kW Inverter for Maximum 24000RPM, ER25 Collet Size Working Area 2050x3050x300mm on X/Y/Z, the Area Spindle Can Reach Working Area Specially Enlarged for South African Market that Offers 2050mm Width for Perspex Accept All Kinds of G-Code File (*.g *.nc *.ug;*.demo;*.iso;*.eng;*.cut;*.dxf;*.plt;*.txt) by USB Flush Drive, G-Code File Size Up to 256M With Standalone EasyRoute Control System, No Computer Needed, Stable System Suitable for Industrial Usage Z-Axis Setter/Presetter Included, Automatic Measure Tool Length & Establish 0 Reference Point Rugged Keypad Against Water, Oil, Dust & Collision, Cheap & Easy to Replace If Damaged 5.5kW 380V Motor, RPM 1440 for Liquid Ring Vacuum Pump, Provide 0.097 MPa Vacuum Level on 8.3 L/min Fluid Flow Rate & 3.83 M 3 /min Air Flow Rate. Just Very Noisy 68dB. Achieve 0.01mm Resolution on All Axis Clampable Vacuum Table Surface Made By Bakelite or Hard Rigid PVC, Very Durable & High Wear-Resistant, Several Aluminium Clamping T-Slots Build In Water-Cooled Chiller Uses Single Phase 220V Household Power, No AC Power Plug Included Total Four Stepper Motors on All Axis, Two Stepper Motors on Y-Axis High-Load, High-Speed Caged Ball Screw Transmission System on... Stock Code: am-r-2030v-55 Items Available: 1 Stock ID: am-r-2030v-55 Send WhatsApp to 0606006000 Johannesburg Branch: Unit 7 Burns Business Park, 12A Jet Park Road, Jet Park 087 802 5368 / 011 397 1429 Cape Town Branch: Unit 6 Alternator Park, 7 Alternator Ave, Montague Gardens 087 802 7106 / 021 555 3250

EasyRoute 380V Standard 2050x4000mm Hard PVC/Bakelite Clampable Vacuum CNC Router, 5kW Water-Cooled Spindle & Stepper Motors,, Vacuum Pump & Dust Collector Full Package R-2040V/50 CNC Router EasyRoute 380V Standard 2050x4000mm Hard PVC/Bakelite Clampable Vacuum CNC.... SKU: R-2040V/50 from AM.CO.ZA CNC Router Price: R325059 excl. valid at 2022-03-20 http://saleprice.co.za/R-2040V/50# Machines / CNC Routers https://buythis.co.za/cnc-routers# CNC Router HE3ADSYS/AMCOZA/R-2040V/50 --- Maximum 20 Meter Per Minute Moving Speed on X/Y Axis,, Factory Default on 12 Meters/Min With Standalone EasyRoute Control System, No Computer Needed, Stable System Suitable for Industrial Usage Accept All Kinds of G-Code File (*.g *.nc *.ug;*.demo;*.iso;*.eng;*.cut;*.dxf;*.plt;*.txt) by USB Flush Drive, G-Code File Size Up to 256M With 100mm Diamter 5kW Water-Cooled Spindle on 7.5kW Inverter (Allow Upgrade to Bigger Spindle) for Maximum 24000RPM, ER20 Collet Size Working Area 2050x4000x300mm on X/Y/Z, the Area Spindle Can Reach Rugged Keypad Against Water, Oil, Dust & Collision, Cheap & Easy to Replace If Damaged Achieve Under 0.5mm Per Meter Accuracy & Repeatability on All Axis High-Load, High-Speed Caged Ball Screw Transmission System on Z Axis DSP Controller use ARM Cortex-A8 800MHz CPU, 512MB Internal Cache & 512MB Flush Memory for Storage Achieve 0.01mm Resolution on All Axis Maximum 5 Meter Per Minute Moving Speed on Z Axis,, Factory Default on 3 Meters/Min Clampable Vacuum Table Surface Made By Bakelite or Hard Rigid PVC, Very Durable & High Wear-Resistant, Several Aluminium Clamping T-Slots Build In Z-Axis Setter/Presetter Included, Automatic Measure Tool Length & Establish 0 Reference Point Total Four Stepper Motors on All Axis, Two Stepper Motors on Y-Axis Use Industrial 380V 3-Phase Electricity, 5 Pin 32A Plug, 4mm Cable Required & Not Included 5.5kW 380V Motor, RPM 1440 for Liquid Ring Vacuum Pump, Provide 0.097 MPa Vacuum Level on 8.3 L/min Fluid Flow Rate & 3.83 M 3 /min Air Flow Rate. Just Very Noisy 68dB. High Precision Rack & Pinion System, Helical Teeth Driving System on X & Y Axis Linear Guide Rail in Twin Parallels Structure & Two Roller Bearing Sliders on Each Rail Guide X/Y/Z Movement With Rotary Attachment Supporting Interface & can Switch between Rotary Rotating & X-Axis Linear Movement --- R-2040V/50: EasyRoute 380V Standard 2050x4000mm Hard PVC/Bakelite Clampable Vacuum CNC Router, 5kW Water-Cooled Spindle & Stepper Motors,, Vacuum Pump & Dust Collector Full Package Price: R325059 excl. WhatsApp 0606006000 / 0722222211 Call 0113971429... Stock Code: am-r-2040v-50 Items Available: 1 Stock ID: am-r-2040v-50 Send WhatsApp to 0606006000 Johannesburg Branch: Unit 7 Burns Business Park, 12A Jet Park Road, Jet Park 087 802 5368 / 011 397 1429 Cape Town Branch: Unit 6 Alternator Park, 7 Alternator Ave, Montague Gardens 087 802 7106 / 021 555 3250

EasyRoute 380V Standard 2050x3050mm Hard PVC/Bakelite Clampable Vacuum CNC Router, 4.5kW High-Torque Water-Cooled Spindle & Stepper Motors R-2030V/45L CNC Router EasyRoute 380V Standard 2050x3050mm Hard PVC/Bakelite Clampable Vacuum CNC... SKU: R-2030V/45L from AM.CO.ZA CNC Router Price: R259999 excl. valid at 2022-03-20 http://saleprice.co.za/R-2030V/45L# Machines / CNC Routers https://buythis.co.za/cnc-routers# CNC Router HE3ADSYS/AMCOZA/R-2030V/45L --- DSP Controller use ARM Cortex-A8 800MHz CPU, 512MB Internal Cache & 512MB Flush Memory for Storage Rugged Keypad Against Water, Oil, Dust & Collision, Cheap & Easy to Replace If Damaged Maximum 5 Meter Per Minute Moving Speed on Z Axis,, Factory Default on 3 Meters/Min Achieve 0.01mm Resolution on All Axis Water-Cooled Chiller Radiating capacity 50W/ C, Energy Saving, Long Working Life Deisng Accept All Kinds of G-Code File (*.g *.nc *.ug;*.demo;*.iso;*.eng;*.cut;*.dxf;*.plt;*.txt) by USB Flush Drive, G-Code File Size Up to 256M Linear Guide Rail in Twin Parallels Structure & Two Roller Bearing Sliders on Each Rail Guide X/Y/Z Movement Total Four Stepper Motors on All Axis, Two Stepper Motors on Y-Axis Maximum 20 Meter Per Minute Moving Speed on X/Y Axis,, Factory Default on 12 Meters/Min Z-Axis Setter/Presetter Included, Automatic Measure Tool Length & Establish 0 Reference Point High Precision Rack & Pinion System, Helical Teeth Driving System on X & Y Axis Water Chiller Maximum Pump Flow Rate 10L/min & Maximum Pump Lift 10 Metres Distance With Rotary Attachment Supporting Interface & can Switch between Rotary Rotating & X-Axis Linear Movement Working Area Specially Enlarged for South African Market that Offers 2050mm Width for Perspex With 125mm Diamter 4.5kW High-Torque Water-Cooled Spindle on 7.5kW Inverter for Maximum 24000RPM, ER25 Collet Size Clampable Vacuum Table Surface Made By Bakelite or Hard Rigid PVC, Very Durable & High Wear-Resistant, Several Aluminium Clamping T-Slots Build In Achieve Under 0.5mm Per Meter Accuracy & Repeatability on All Axis Chiller Water Tank Capacity 9L, Purified Water Required (Not Supplied), Replace Monthly Suggested With Standalone EasyRoute Control System, No Computer Needed, Stable System Suitable for Industrial Usage High-Load, High-Speed Caged Ball Screw Transmission System on Z Axis Use Industrial 380V 3-Phase Electricity, 5 Pin 32A Plug, 4mm Cable Required & Not Included Working Area 2050x3050x300mm on X/Y/Z, the Area Spindle Can Reach Water-Cooled Chiller Uses Single Phase 220V Household Power, No AC Power Plug Included ---... Stock Code: am-r-2030v-45l Items Available: 1 Stock ID: am-r-2030v-45l Send WhatsApp to 0606006000 Johannesburg Branch: Unit 7 Burns Business Park, 12A Jet Park Road, Jet Park 087 802 5368 / 011 397 1429 Cape Town Branch: Unit 6 Alternator Park, 7 Alternator Ave, Montague Gardens 087 802 7106 / 021 555 3250

EasyRoute 380V Standard 2050x4000mm PVC Clampable Vacuum CNC Router, 7.5kW High-Torque Low RPM Water-Cooled Spindle & Stepper Motors,, Vacuum Pump & Dust Collector Full Package R-2040K/75 CNC Router EasyRoute 380V Standard 2050x4000mm PVC Clampable Vacuum CNC Router, 7.5kW.... SKU: R-2040K/75 from AM.CO.ZA CNC Router Price: R345059 excl. valid at 2022-03-20 http://saleprice.co.za/R-2040K/75# Machines / CNC Routers https://buythis.co.za/cnc-routers# CNC Router HE3ADSYS/AMCOZA/R-2040K/75 --- Total Four Stepper Motors on All Axis, Two Stepper Motors on Y-Axis Achieve 0.01mm Resolution on All Axis Water-Cooled Chiller Radiating capacity 50W/ C, Energy Saving, Long Working Life Deisng With 125mm Diamter 7.5kW High-Torque Low RPM Water-Cooled Spindle for Aluminium Machining 5.5kW 380V Motor, RPM 1440 for Liquid Ring Vacuum Pump, Provide 0.097 MPa Vacuum Level on 8.3 L/min Fluid Flow Rate & 3.83 M 3 /min Air Flow Rate. Just Very Noisy 68dB. With Rotary Attachment Supporting Interface & can Switch between Rotary Rotating & X-Axis Linear Movement Clampable Vacuum Table Surface Made By PVC, Aluminium Clamping T-Slots Build In Z-Axis Setter/Presetter Included, Automatic Measure Tool Length & Establish 0 Reference Point DSP Controller use ARM Cortex-A8 800MHz CPU, 512MB Internal Cache & 512MB Flush Memory for Storage High-Load, High-Speed Caged Ball Screw Transmission System on Z Axis Linear Guide Rail in Twin Parallels Structure & Two Roller Bearing Sliders on Each Rail Guide X/Y/Z Movement Rugged Keypad Against Water, Oil, Dust & Collision, Cheap & Easy to Replace If Damaged Accept All Kinds of G-Code File (*.g *.nc *.ug;*.demo;*.iso;*.eng;*.cut;*.dxf;*.plt;*.txt) by USB Flush Drive, G-Code File Size Up to 256M Achieve Under 0.5mm Per Meter Accuracy & Repeatability on All Axis High Precision Rack & Pinion System, Helical Teeth Driving System on X & Y Axis Chiller Water Tank Capacity 9L, Purified Water Required (Not Supplied), Replace Monthly Suggested Water Chiller Maximum Pump Flow Rate 10L/min & Maximum Pump Lift 10 Metres Distance Working Area 2050x4000x300mm on X/Y/Z, the Area Spindle Can Reach Water-Cooled Chiller Uses Single Phase 220V Household Power, No AC Power Plug Included With Standalone EasyRoute Control System, No Computer Needed, Stable System Suitable for Industrial Usage Maximum 5 Meter Per Minute Moving Speed on Z Axis,, Factory Default on 3 Meters/Min Use Industrial 380V 3-Phase Electricity, 5 Pin 32A Plug, 4mm Cable Required & Not Included Maximum 20 Meter Per Minute Moving Speed on X/Y Axis,, Factory Default on 12 Meters/Min... Stock Code: am-r-2040k-75 Items Available: 1 Stock ID: am-r-2040k-75 Send WhatsApp to 0606006000 Johannesburg Branch: Unit 7 Burns Business Park, 12A Jet Park Road, Jet Park 087 802 5368 / 011 397 1429 Cape Town Branch: Unit 6 Alternator Park, 7 Alternator Ave, Montague Gardens 087 802 7106 / 021 555 3250

EasyRoute Heavy Duty CNC Router 2000 3000 Vacuum Table, Servo, 9kW ATC Spindle SKU: R2-2030V/90L from Buythis.co.za Online Store Price: R579999 excl. valid at 2022-04-06, Nationwide FREE Shipping for Online Orders Ts/Cs https://buythis.co.za/r2-2030v-90l# HE3ADSYS/BUYTHIS/R2-2030V/90L Machines / CNC Routers / Furniture CNC Routers EasyRoute Heavy Duty CNC Router with Linear Automatic Tool Change ATC Tested on 16mm Perspex Cutting https://youtu.be/pHTo0vHLoag# --- Linear Guide Rail in Twin Parallels Structure & Two Roller Bearing Sliders on Each Rail Guide X/Y/Z Movement High Precision Rack & Pinion System, Helical Teeth Driving System on X & Y Axis Servo Motors Give Your Much Better Accuracy, Much Faster Speed & Much More Torch. Total 4 Servo Motors Used, Two on Y-Axis Rugged Keypad Against Water, Oil, Dust & Collision, Cheap & Easy to Replace If Damaged Maximum 80 Meter Per Minute Moving Speed on X/Y Axis,, Factory Default on 25 Meters/Min Heavy Duty Version Much More Accurate & Better Performance on Long Run, Double the Warranty Time With 9kW Air-Cooled ATC Automatic-Tool-Changer Spindle for Maximum 24000RPM, ISO30 Tool Holder on ER32 Collet Size Achieve Under 0.05mm Per Meter Accuracy & Repeatability on All Axis Maximum 5 Meter Per Minute Moving Speed on Z Axis,, Factory Default on 3 Meters/Min With Rotary Attachment Supporting Interface & can Switch between Rotary Rotating & X-Axis Linear Movement DSP Controller use ARM Cortex-A8 800MHz CPU, 512MB Internal Cache & 512MB Flush Memory for Storage With Standalone EasyRoute Control System, No Computer Needed, Stable System Suitable for Industrial Usage Clampable Vacuum Table Surface Made By Bakelite or Hard Rigid PVC, Very Durable & High Wear-Resistant, Several Aluminium Clamping T-Slots Build In High-Load, High-Speed Caged Ball Screw Transmission System on Z Axis Z-Axis Setter/Presetter Included, Automatic Measure Tool Length & Establish 0 Reference Point Working Area 2050x3050x300mm on X/Y/Z, the Area Spindle Can Reach Accept All Kinds of G-Code File (*.g *.nc *.ug;*.demo;*.iso;*.eng;*.cut;*.dxf;*.plt;*.txt) by USB Flush Drive, G-Code File Size Up to 256M Achieve 0.01mm Resolution on All Axis Use Industrial 380V 3-Phase Electricity, 5 Pin 32A Plug, 4mm Cable Required & Not Included Automatic Linear Tool Change, a Tool Rack for 16 Tools, ISO30 Tool Holder, Default ER32 Collet Working Area Specially Enlarged for South African Market that Offers 2050mm Width for Perspex --- EasyRoute Heavy Duty CNC Router 2000 3000 Vacuum Table, Servo, 9kW ATC.. Buythis.co.za R2-2030V/90... Stock Code: bt-r2-2030v-90l Items Available: 1 Stock ID: bt-r2-2030v-90l Send WhatsApp to 0606006000 Johannesburg Branch: Unit 7 Burns Business Park, 12A Jet Park Road, Jet Park 087 802 5368 / 011 397 1429 Cape Town Branch: Unit 6 Alternator Park, 7 Alternator Ave, Montague Gardens 087 802 7106 / 021 555 3250

EasyRoute 380V Standard 1300x2500mm PVC Clampable Vacuum CNC Router, 5.5kW High-Torque Water-Cooled Spindle & Stepper Motors,, Vacuum Pump & Dust Collector Full Package R-1325K/55 CNC Router EasyRoute 380V Standard 1300x2500mm PVC Clampable Vacuum CNC Router, 5.5kW.... SKU: R-1325K/55 from AM.CO.ZA CNC Router Price: R141299 excl. valid at 2022-04-06 http://saleprice.co.za/R-1325K/55# Machines / CNC Routers https://buythis.co.za/cnc-routers# CNC Router HE3ADSYS/AMCOZA/R-1325K/55 --- DSP Controller use ARM Cortex-A8 800MHz CPU, 512MB Internal Cache & 512MB Flush Memory for Storage 5.5kW 380V Motor, RPM 1440 for Liquid Ring Vacuum Pump, Provide 0.097 MPa Vacuum Level on 8.3 L/min Fluid Flow Rate & 3.83 M 3 /min Air Flow Rate. Just Very Noisy 68dB. Water-Cooled Chiller Uses Single Phase 220V Household Power, No AC Power Plug Included High-Load, High-Speed Caged Ball Screw Transmission System on Z Axis Maximum 20 Meter Per Minute Moving Speed on X/Y Axis,, Factory Default on 12 Meters/Min Z-Axis Setter/Presetter Included, Automatic Measure Tool Length & Establish 0 Reference Point Linear Guide Rail in Twin Parallels Structure & Two Roller Bearing Sliders on Each Rail Guide X/Y/Z Movement Working Area 1300x2500x300mm on X/Y/Z, the Area Spindle Can Reach Achieve 0.01mm Resolution on All Axis Maximum 5 Meter Per Minute Moving Speed on Z Axis,, Factory Default on 3 Meters/Min Accept All Kinds of G-Code File (*.g *.nc *.ug;*.demo;*.iso;*.eng;*.cut;*.dxf;*.plt;*.txt) by USB Flush Drive, G-Code File Size Up to 256M Water-Cooled Chiller Radiating capacity 50W/ C, Energy Saving, Long Working Life Deisng Clampable Vacuum Table Surface Made By PVC, Aluminium Clamping T-Slots Build In With Standalone EasyRoute Control System, No Computer Needed, Stable System Suitable for Industrial Usage With 125mm Diamter 5.5kW High-Torque Water-Cooled Spindle on 7.5kW Inverter for Maximum 24000RPM, ER25 Collet Size Achieve Under 0.5mm Per Meter Accuracy & Repeatability on All Axis Rugged Keypad Against Water, Oil, Dust & Collision, Cheap & Easy to Replace If Damaged Use Industrial 380V 3-Phase Electricity, 5 Pin 32A Plug, 4mm Cable Required & Not Included High Precision Rack & Pinion System, Helical Teeth Driving System on X & Y Axis Water Chiller Maximum Pump Flow Rate 10L/min & Maximum Pump Lift 10 Metres Distance Total Four Stepper Motors on All Axis, Two Stepper Motors on Y-Axis Chiller Water Tank Capacity 9L, Purified Water Required (Not Supplied), Replace Monthly Suggested With Rotary Attachment Supporting Interface & can Switch between Rotary Rotating & X-Axi... Stock Code: am-r-1325k-55 Items Available: 1 Stock ID: am-r-1325k-55 Send WhatsApp to 0606006000 Johannesburg Branch: Unit 7 Burns Business Park, 12A Jet Park Road, Jet Park 087 802 5368 / 011 397 1429 Cape Town Branch: Unit 6 Alternator Park, 7 Alternator Ave, Montague Gardens 087 802 7106 / 021 555 3250

EasyRoute 380V Standard 2050x3050mm PVC Clampable Vacuum CNC Router, 4.5kW High-Torque Water-Cooled Spindle & Stepper Motors R-2030K/45L CNC Router EasyRoute 380V Standard 2050x3050mm PVC Clampable Vacuum CNC Router, 4.5kW... SKU: R-2030K/45L from AM.CO.ZA CNC Router Price: R229999 excl. valid at 2022-04-06 http://saleprice.co.za/R-2030K/45L# Machines / CNC Routers https://buythis.co.za/cnc-routers# CNC Router HE3ADSYS/AMCOZA/R-2030K/45L --- Linear Guide Rail in Twin Parallels Structure & Two Roller Bearing Sliders on Each Rail Guide X/Y/Z Movement With Standalone EasyRoute Control System, No Computer Needed, Stable System Suitable for Industrial Usage Z-Axis Setter/Presetter Included, Automatic Measure Tool Length & Establish 0 Reference Point Accept All Kinds of G-Code File (*.g *.nc *.ug;*.demo;*.iso;*.eng;*.cut;*.dxf;*.plt;*.txt) by USB Flush Drive, G-Code File Size Up to 256M With Rotary Attachment Supporting Interface & can Switch between Rotary Rotating & X-Axis Linear Movement Water-Cooled Chiller Radiating capacity 50W/ C, Energy Saving, Long Working Life Deisng Achieve Under 0.5mm Per Meter Accuracy & Repeatability on All Axis Water-Cooled Chiller Uses Single Phase 220V Household Power, No AC Power Plug Included Chiller Water Tank Capacity 9L, Purified Water Required (Not Supplied), Replace Monthly Suggested Working Area Specially Enlarged for South African Market that Offers 2050mm Width for Perspex With 125mm Diamter 4.5kW High-Torque Water-Cooled Spindle on 7.5kW Inverter for Maximum 24000RPM, ER25 Collet Size Working Area 2050x3050x300mm on X/Y/Z, the Area Spindle Can Reach Achieve 0.01mm Resolution on All Axis Maximum 20 Meter Per Minute Moving Speed on X/Y Axis,, Factory Default on 12 Meters/Min Maximum 5 Meter Per Minute Moving Speed on Z Axis,, Factory Default on 3 Meters/Min Clampable Vacuum Table Surface Made By PVC, Aluminium Clamping T-Slots Build In DSP Controller use ARM Cortex-A8 800MHz CPU, 512MB Internal Cache & 512MB Flush Memory for Storage High Precision Rack & Pinion System, Helical Teeth Driving System on X & Y Axis High-Load, High-Speed Caged Ball Screw Transmission System on Z Axis Total Four Stepper Motors on All Axis, Two Stepper Motors on Y-Axis Water Chiller Maximum Pump Flow Rate 10L/min & Maximum Pump Lift 10 Metres Distance Use Industrial 380V 3-Phase Electricity, 5 Pin 32A Plug, 4mm Cable Required & Not Included Rugged Keypad Against Water, Oil, Dust & Collision, Cheap & Easy to Replace If Damaged --- R-2030K/45L: EasyRoute 380V Standard 2050x3050mm PVC Clampable Vacuum CNC Router... Stock Code: am-r-2030k-45l Items Available: 1 Stock ID: am-r-2030k-45l Send WhatsApp to 0606006000 Johannesburg Branch: Unit 7 Burns Business Park, 12A Jet Park Road, Jet Park 087 802 5368 / 011 397 1429 Cape Town Branch: Unit 6 Alternator Park, 7 Alternator Ave, Montague Gardens 087 802 7106 / 021 555 3250

EasyRoute Heavy Duty 380V Standard 2050x3050mm Hard PVC/Bakelite Clampable Vacuum CNC Router, 9kW Air-Cooled ATC Spindle & Servo Motors,, 5.5kW Liquid Ring Vacuum Pump SKU: R2-2030V/90V from Buythis.co.za Online Store Price: R595139 excl. valid at 2022-04-15, Nationwide FREE Shipping for Online Orders Ts/Cs https://buythis.co.za/r2-2030v-90v# HE3ADSYS/BUYTHIS/R2-2030V/90V Machines / CNC Routers / Furniture CNC Routers Tuff Cases Made by Tough Machines, AM CNC Router Helps CPS Make Tough Cases https://youtu.be/6cYQP7cwhWk# --- With Standalone EasyRoute Control System, No Computer Needed, Stable System Suitable for Industrial Usage Accept All Kinds of G-Code File (*.g *.nc *.ug;*.demo;*.iso;*.eng;*.cut;*.dxf;*.plt;*.txt) by USB Flush Drive, G-Code File Size Up to 256M Working Area Specially Enlarged for South African Market that Offers 2050mm Width for Perspex Automatic Linear Tool Change, a Tool Rack for 16 Tools, ISO30 Tool Holder, Default ER32 Collet Maximum 5 Meter Per Minute Moving Speed on Z Axis,, Factory Default on 3 Meters/Min Z-Axis Setter/Presetter Included, Automatic Measure Tool Length & Establish 0 Reference Point High-Load, High-Speed Caged Ball Screw Transmission System on Z Axis 5.5kW 380V Motor, RPM 1440 for Liquid Ring Vacuum Pump, Provide 0.097 MPa Vacuum Level on 8.3 L/min Fluid Flow Rate & 3.83 M 3 /min Air Flow Rate. Just Very Noisy 68dB. DSP Controller use ARM Cortex-A8 800MHz CPU, 512MB Internal Cache & 512MB Flush Memory for Storage Achieve Under 0.05mm Per Meter Accuracy & Repeatability on All Axis Rugged Keypad Against Water, Oil, Dust & Collision, Cheap & Easy to Replace If Damaged Working Area 2050x3050x300mm on X/Y/Z, the Area Spindle Can Reach Use Industrial 380V 3-Phase Electricity, 5 Pin 32A Plug, 4mm Cable Required & Not Included With 9kW Air-Cooled ATC Automatic-Tool-Changer Spindle for Maximum 24000RPM, ISO30 Tool Holder on ER32 Collet Size Linear Guide Rail in Twin Parallels Structure & Two Roller Bearing Sliders on Each Rail Guide X/Y/Z Movement High Precision Rack & Pinion System, Helical Teeth Driving System on X & Y Axis Achieve 0.01mm Resolution on All Axis Clampable Vacuum Table Surface Made By Bakelite or Hard Rigid PVC, Very Durable & High Wear-Resistant, Several Aluminium Clamping T-Slots Build In Servo Motors Give Your Much Better Accuracy, Much Faster Speed & Much More Torch. Total 4 Servo Motors Used, Two on Y-Axis Maximum 80 Meter Per Minute Moving Speed on X/Y Axis,, Factory Default on 25 Meters/Min With Rotary Attachment Supporting Interface & can Switch between Rotary Rotating & X... Stock Code: bt-r2-2030v-90v Items Available: 1 Stock ID: bt-r2-2030v-90v Send WhatsApp to 0606006000 Johannesburg Branch: Unit 7 Burns Business Park, 12A Jet Park Road, Jet Park 087 802 5368 / 011 397 1429 Cape Town Branch: Unit 6 Alternator Park, 7 Alternator Ave, Montague Gardens 087 802 7106 / 021 555 3250

EasyRoute 380V Standard 2050x3050mm PVC Clampable Vacuum CNC Router, 5.5kW High-Torque Water-Cooled Spindle & Stepper Motors,, 5.5kW Liquid Ring Vacuum Pump SKU: R-2030K/55V from Buythis.co.za Online Store Price: R165139 excl. valid at 2022-04-20, Nationwide FREE Shipping for Online Orders Ts/Cs https://buythis.co.za/r-2030k-55v# HE3ADSYS/BUYTHIS/R-2030K/55V Machines / CNC Routers / Signage CNC Routers --- With Rotary Attachment Supporting Interface & can Switch between Rotary Rotating & X-Axis Linear Movement DSP Controller use ARM Cortex-A8 800MHz CPU, 512MB Internal Cache & 512MB Flush Memory for Storage Achieve 0.01mm Resolution on All Axis Linear Guide Rail in Twin Parallels Structure & Two Roller Bearing Sliders on Each Rail Guide X/Y/Z Movement Chiller Water Tank Capacity 9L, Purified Water Required (Not Supplied), Replace Monthly Suggested Rugged Keypad Against Water, Oil, Dust & Collision, Cheap & Easy to Replace If Damaged Working Area Specially Enlarged for South African Market that Offers 2050mm Width for Perspex Working Area 2050x3050x300mm on X/Y/Z, the Area Spindle Can Reach Z-Axis Setter/Presetter Included, Automatic Measure Tool Length & Establish 0 Reference Point Total Four Stepper Motors on All Axis, Two Stepper Motors on Y-Axis Use Industrial 380V 3-Phase Electricity, 5 Pin 32A Plug, 4mm Cable Required & Not Included Maximum 20 Meter Per Minute Moving Speed on X/Y Axis,, Factory Default on 12 Meters/Min High Precision Rack & Pinion System, Helical Teeth Driving System on X & Y Axis High-Load, High-Speed Caged Ball Screw Transmission System on Z Axis Water-Cooled Chiller Radiating capacity 50W/ C, Energy Saving, Long Working Life Deisng Clampable Vacuum Table Surface Made By PVC, Aluminium Clamping T-Slots Build In Achieve Under 0.5mm Per Meter Accuracy & Repeatability on All Axis Maximum 5 Meter Per Minute Moving Speed on Z Axis,, Factory Default on 3 Meters/Min With 125mm Diamter 5.5kW High-Torque Water-Cooled Spindle on 7.5kW Inverter for Maximum 24000RPM, ER25 Collet Size Accept All Kinds of G-Code File (*.g *.nc *.ug;*.demo;*.iso;*.eng;*.cut;*.dxf;*.plt;*.txt) by USB Flush Drive, G-Code File Size Up to 256M With Standalone EasyRoute Control System, No Computer Needed, Stable System Suitable for Industrial Usage Water Chiller Maximum Pump Flow Rate 10L/min & Maximum Pump Lift 10 Metres Distance Water-Cooled Chiller Uses Single Phase 220V Household Power, No AC Power Plug Included 5.5kW 380V Motor, RPM 1440 for Liquid Ring Vacuum Pump, Provide 0.097 MPa Vacuum Level on 8.3 L/min Fluid Flow Rate & 3.83 M 3 /min Air Flow Rate. Just... Stock Code: bt-r-2030k-55v Items Available: 1 Stock ID: bt-r-2030k-55v Send WhatsApp to 0606006000 Johannesburg Branch: Unit 7 Burns Business Park, 12A Jet Park Road, Jet Park 087 802 5368 / 011 397 1429 Cape Town Branch: Unit 6 Alternator Park, 7 Alternator Ave, Montague Gardens 087 802 7106 / 021 555 3250