Full modular cable management

Buy Corsair CP-9020140 HX1200, 14x full Modular cable management (all cable detachable), switch for R5,186.00

Buy Corsair Cp-9020140 Hx1200, 14X Full Modular Cable Management (All Cable Detachable), Switch for R5,039.00

Buy Corsair CP-9020101 CX450M, with 4x Modular cable management, Eps12V, ATX 12V V2.3 - 450w, 8 for R1,063.00

The FSP DAGGER PRO ATX3.0 750W is a power supply with 80 PLUS® Gold Certification that guarantees to operate at a minimum of 90% efficiency at 50% load of PSU-rated power and as a result, reduces lots of electricity cost. The Fully-modular design and flat ribbon cables provide easier installation. An ideal solution for applications with space constraints, enhancing overall airflow efficiency and cable management. The DAGGER PRO 750W comes with a native PCIe 5.0 connector for the latest graphic cards and features dual CPU power connectors to support high-end motherboards for gaming enthusiasts. The VGA card is a component which needs greedy and stable power support most. The compact-sized DAGGER PRO ATX3.0 750W comes with a single +12V rail design that offers VGA cards full power individually and to avoid any overloading conditions. It is compatible with most Mini-ITX and Micro ATX small form factor PCs. It is ideal for home computer rigs but a great alternative for mini-PC enthusiasts. It Adapts to your individual requirements, not only does it fit into cases with the SFX form factor but can also be installed easily into normal ATX, Micro-ATX or Mini-ITX cases. FEATURES: Compliance with ATX12V V3.0 Compliance with PCIe 5.0 Efficiency ≧ 90% at typical load MIA IC (Multiple Intelligence Ability) chipset inside Semi-Fanless design for silent operation Quiet and long-lasting 92mm ball bearing fan Ribbon cables for the need of enthusiasts Powerful single +12V rail design Intel’s Latest CPU ready Japanese electrolytic capacitors Full protections with OCP, OVP, SCP, OPP, OTP SPECIFICATIONS: Rated Output Power: 750W Form Factor: SFX 80 PLUS Certification: Gold Input Voltage: 100-240V Input Current: 12-6A Input Frequency: 50-60Hz PFC: Active PFC Efficiency: 90% Fan Type: ball bearing fan,92mm Operation Temp: 200,000 Hrs Protection: OCP, OVP, SCP, OPP, OTP AC Input: 100-240Vac~ 12-6A 50-60Hz DC Output: +3.3V(20A), +5V(20A), +12V(70.83A), -12V(0.3A), +5Vsb(2.5A) Connectors: ATX 20+4 x1 4+4 PIN x2 PCIe 6+2 x4 12VHPWR x1 SATA x6 Molex (peripheral) x2 Product Dimensions: 12.5 × 10 × 6.4 cm WHAT’S IN THE BOX: FSP DAGGER PRO 750W Modular PSU x1 Modular Cables Set x1

The DAGGER PRO 850W is a power supply with 80 PLUS® Gold Certification that guarantees to operate at a minimum of 90% efficiency at 50% the load of the PSU-rated power and as a result, reduces lots of electricity costs. The Fully-modular design and flat ribbon cables provide easier installation. An ideal solution for applications with space constraints, enhancing overall airflow efficiency and cable management. The DAGGER PRO 850W comes with a native PCIe 5.0 connector for the latest graphic card and features dual CPU power connectors to support high-end motherboards for gaming enthusiasts. The VGA card is a component which needs greedy and stable power support most. The compact-sized DAGGER PRO ATX3.0 850W comes with a single +12V rail design that offers VGA cards full power individually and to avoid any overloading conditions. It is compatible with most Mini-ITX and Micro ATX small form factor PCs. It is ideal for home computer rigs but a great alternative for mini-PC enthusiasts. It Adapts to your individual requirements, not only does it fit into cases with the SFX form factor but can also be installed in a simple step into normal ATX, Micro-ATX or Mini-ITX cases. FEATURES: Compliance with ATX12V V3.0 Compliance with PCIe 5.0 Efficiency ≧ 90% at typical load MIA IC (Multiple Intelligence Ability) chipset inside Semi-fanless design for silent operation Quiet and long-lasting 92mm ball bearing fan Ribbon cables for the need of enthusiasts Powerful single +12V rail design Intel’s Latest CPU ready Japanese electrolytic capacitors Full protections with OCP, OVP, SCP, OPP, OTP SPECIFICATIONS: Rated Output Power: 850W Form Factor: SFX 80 PLUS Certification: Gold Input Voltage: 100-240V Input Current: 12-6A Input Frequency: 50-60Hz PFC: Active PFC Efficiency: 90% Fan Type: ball bearing fan,92mm Operation Temp: 200,000 Hrs Protection: OCP, OVP, SCP, OPP, OTP AC Input: 100-240Vac~ 12-6A 50-60Hz DC Output: +3.3V(20A), +5V(20A), +12V(70.83A), -12V(0.3A), +5Vsb(2.5A) Connectors: ATX 20+4 x1 4+4 PIN x2 PCIe 6+2 x4 12VHPWR x1 SATA x6 Molex (peripheral) x2 Product Dimensions: 12.5 × 10 × 6.4 cm WHAT’S IN THE BOX: FSP DAGGER PRO 850W Modular PSU x1 Modular Cables Set x1

Presenting the Antec NE850G M ATX 3.0 power supply, intended for the gaming and enthusiast markets with maximum performance and stability in mind. You can expect peak performance from your system with modern features like ATX 3.0 and high-quality JP capacitors, unrivalled stability, and 80 PLUS® Gold-certified efficiency. The PhaseWave Design guarantees consistent power output, while the 120mm FDB Quiet Fan provides silent cooling. The power supply is also 100% modular, making wire management and customization a breeze. The Zero RPM Manager provides superior thermal control, ensuring the best balance of silent operation and efficient cooling. The CircuitShield industrial-grade protection suite ensures safe and dependable power delivery in any situation. The Antrec NE850G M ATX 3.0 is ideal for constructing a dependable and efficient PC system for gamers and professionals. Features: Fully-Modular 850W continuous power 80 PLUS® ATX 3.0 & PCIe 5.0 Compatible High-Quality JP Capacitors PhaseWave Design 120mm FDB Silent Fan Antec CircuitShield™ – A full suite of industrial-grade protection Specifications: Modularity: Fully Modular Output Capacity: 850W Input Voltage: 200-240 V Input Current: 10A-5A Input Frequency Range: 50Hz-60Hz PFC: Active PFC Power Good Signal: 100-150ms Efficiency: 80 Plus Gold Protection: OCP, OVP, UVP, SCP, OPP, OTP, SIP, NLO Regulatory: cTUVus / TUV / CB / RCM / CE / FCC / BIS / BSMI / KC / UKCA / ICES Fan: 120mm FBD Silent Fan Certifications: 80 Plus Connectors: 1 x 24(20+4)pin MB 1 x 16(12+4)pin PCIE 5.0 12VHPWR 2 x 8(4+4)pin CPU 4 x 8(6+2) Pin PCI-E 12 x SATA 4 x Molex Product Dimensions: 14 x 15 x 8.6 cm What’s In The Box: Antec NE850G M ATX 3.0 Modular ATX Power Supply – Black x1 Modular Cables set x1

Presenting the Antec NE1000G M ATX 3.0 power supply, intended for the gaming and enthusiast markets with maximum performance and stability in mind. You can expect peak performance from your system with modern features like ATX 3.0 and high-quality JP capacitors, unrivalled stability, and 80 PLUS® Gold-certified efficiency. The PhaseWave™ Design guarantees consistent power output, while the 120mm FDB Quiet Fan provides silent cooling. The power supply is also 100% modular, making wire management and customization a breeze. The Zero RPM Manager provides superior thermal control, ensuring the best balance of silent operation and efficient cooling. The CircuitShield™ industrial-grade protection suite ensures safe and dependable power delivery in any situation. The Antec NE1000G M ATX 3.0 is the perfect choice for building a reliable and efficient PC system for gamers and professionals. Features: Fully-Modular 1000W continuous power 80 PLUS® ATX 3.0 & PCIe 5.0 Compatible High-Quality JP Capacitors PhaseWave TM Design 120mm FDB Silent Fan Antec CircuitShield™ – A full suite of industrial-grade protection Specifications: Modularity: Fully Modular Output Capacity: 1000W Input Voltage: 200-240 V Input Current: 12A-6A Input Frequency Range: 50Hz-60Hz PFC: Active PFC Power Good Signal: 100-150ms Efficiency: 80 Plus Gold Protection: OCP, OVP, UVP, SCP, OPP, OTP, SIP, NLO Regulatory: cTUVus / TUV / CB / RCM / CE / FCC / BIS / BSMI / KC / UKCA / ICES Fan: 120mm FBD Silent Fan Certifications: 80 Plus Connectors: 1 x 24(20+4)pin MB 1 x 16(12+4)pin PCIE 5.0 12VHPWR 2 x 8(4+4)pin CPU 4 x 8(6+2) Pin PCI-E 12 x SATA 4 x Molex Product Dimensions: 14 x 15 x 8.6 cm What’s In The Box: Antec NE850G M ATX 3.0 Modular ATX Power Supply – Black x1

AOC MONITOR 19.5″ TN PANEL, 1600X900 19.5-inch viewable; Full HD ergonomic business display The 20E1H boasts a 19.5″ TN panel, 1600×900 resolution with HDMI and legacy VGA inputs (cables included). Stand offers tilting and cable management. Certified green.

TP-Link TL-MR100 300 Mbps Wireless N 4G LTE Router Features: No Configuration Needed Simply Plug and Play! With an integrated 4G LTE modem and a built-in SIM card slot, all you need to do is inserting a micro SIM card and turning on the router. It has never been easier than enjoy a fast, stable Wi-Fi on 4G LTE network. Share Your 4G LTE Network Take full advantage of your cutting-edge 4G LTE network to download speed up to 150 Mbps. Share your 4G LTE network with multiple Wi-Fi devices and enjoy uninterrupted HD movies, rapid file downloads, and smooth video chats. Fully compatible with FDD-LTE and TDD-LTE to work with most service providers worldwide. Robust Parental Controls If you want to block harmful websites, set surfing time limits, check which sites your kids are using or just pause the internet, you can do it all. Guest Network It provides separate Wi-Fi access for guests while securing the whole network. Wi-Fi Where You Need It Enjoy unconstrained convenience and versatility. MR100 has been tested in the field for years to ensure universal compatibility with 2 advanced LTE antennas to deliver a smooth connection. Simply plug in a micro SIM card and power on this elegant piece of device to utilize fast and stable Wi-Fi, whether you’re at home or working remotely. Reliable Access for Up to 32 Devices Simultaneously Easily share a 3G/4G connection with up to 32 wireless devices, such as phones, tablets, and laptops, at the same time. 4 LAN ports stand ready to provide internet for wired devices like desktop computers. Specifications: Product Code TL-MR100 HARDWARE FEATURES Interface 1 10/100Mbps LAN Port, 1 10/100Mbps LAN/WAN Port 1 Micro SIM Card Slot Button WPS/Reset Button External Power Supply(EU) 9V/0.85A Dimensions (W x D x H) 6.06×4.49×1.42 in (154x114x36 mm) Antenna 2 Detachable External 4G LTE Antennas WIRELESS FEATURES Wireless Standards IEEE 802.11b/g/n Frequency 2.4 GHz Signal Rate 300 Mbps Reception Sensitivity 11g 54M: -74 dBm 11n HT20: -71 dBm 11n HT40: -68 dBm Transmit Power b' Wireless Functions Enable/Disable Wireless Radio, Wireless Schedule, WMM, Wireless Statistics WAN Failover Yes Wireless Security 64/128-bit WEP, WPA/WPA2, WPA-PSK/WPA2-PSK encryptions Network Type 4G: FDD-LTE: B1/B3/B5/B7/B8/B20 (2100/1800/850/2600/900/800 MHz) TDD-LTE: B38/B40/B41 (2600/2300/2500 MHz) 3G: HSPA/UMTS: B1/B5/B8 (2100/850/900 MHz) SOFTWARE FEATURES Security IPv4 SPI Firewall, IP and MAC Address Binding Operating Modes 3G/4G Router, Wireless Router WAN Type Dynamic IP/Static IP/PPPoE/PPTP(Dual Access)/L2TP(Dual Access) Management Local Management, Remote Management DHCP Server, DHCP Client List, Address Reservation Port Forwarding ALG, Virtual Server, Port Triggering, UPnP, DMZ Dynamic DNS DynDns, NO-IP Protocols IPv4, IPv6 Guest Network 2.4 GHz Guest Network Administration Upgrade Firmware, Factory Default, System Log, Diagnostic Tools OTHERS Certification CE, RoHS Package Contents 300 Mbps Wireless N 4G LTE TL-MR100 Power Adapter RJ45 Ethernet Cable Quick Installation Guide Requirements Microsoft Windows 98SE/NT/2000/XP/Vista /7/8/8.1/10, MAC OS NetWare, UNIX or Linux Internet Explorer 11, Firefox 12.0, Chrome 20.0, Safari 4.0, or other Java-enabled browser Micro SIM Card Environment Operating Temperature: 0°C~40°C (32°F ~104°F) Storage Temperature: -40°C~70°C (-40°F ~158°F) Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~90% non-condensing

Tenda TEG1124P-24-250W 24-Port Gigabit Ethernet Switch TEG1124P-24-250W is a Tenda Gigabit Ethernet PoE switch that o ers 24 10/100/1000 Mbps Base-TX RJ45 ports. Ports 1-24 comply with the IEEE 802.3af standard (maximum PoE power output: 15.4 W) and 802.3at standard (maximum PoE power output: 30 W). The switch o ers a maximum PoE power output of 225 W and can supply power to and exchange data with APs, IP cameras, and IP phones through CAT5 cables. It also provides simple management modes such as CCTV, VLAN, and Isolation to help reduce cabling costs of IP terminals like APs and IP cameras 6KV Lightning Protection PoE Switch is the only engineering switch In real projects, APs and cameras are often installed outdoors or at an elevated location, which increases the chance of lightning strikes on cameras and PoE-powered switches. The result is that individual devices are damaged when the outcome is light, and even the whole local area network is damaged. Tenda TEG11 series switches have a professional lightning protection design – 6KV Lightning Protection for Ports and the power, and they have two levels of protection design respectively, which effectively suppress the lightning current from the network cable and power supply, equivalent to adding a security wall to the entire network monitoring system. The test standard is much higher than the national CCCrequest. In the thunderstorm, Tenda TEG11 series switches can also provide a stable and reliable service to the surveillance network and guarantee the normal transmission of the picture. CCTV, Standard, VLAN and Isolation Operation Modes Offered CCTV: in this mode, the port cache is optimized and PoE ports 1-8 have higher priorities over the other ports. All the ports of the switch can communicate with each other. If multiple IP cameras are connected to the switch, you are recommended to enable this mode and connect the uplink port of the switch to the upstream device to which the monitoring computer connects. This ensures smoother monitoring video playback. Standard: the switch functions as a common unmanaged switch and all the ports of the switch can communicate with each other. VLAN: ports 1 to 22 of TEG1124P-24-250W are isolated from each other, but can communicate with ports 23 and 24 (uplink ports) respectively.Solid DIP switch to isolate ports to prevent broadcast storm and defend DHCP spoofing. Isolation: ports 1 to 12 and Ports 13 to 24 of TEG1124P-24-250W belong to two different VLAN. This mode can be used to isolate supervision network and wireless network to make them not interfere with each other. 225W PoE power supply simplified wiring Ports 1-24 comply with the IEEE802.3af and IEEE802.3at power supply standards. The entire switch offers a maximum PoE power output of 225W, whereas each port offers a maximum PoE power output of 30 W. The ports can be used to supply power to and exchange data with APs and IP cameras. Specifications Standard b'&' Protocol IEEE 802.3/IEEE 802.3u/IEEE 802.3ab/IEEE 802.3x/IEEE 802.3af/IEEE 802.3at Indicator 24*Link/Act per device 24*PoE per device 1*Power per device Interface 24 10/100/1000Base-T ports(Data/Power) Lightning Protection 6KV Store b'&' Forward Yes exchange capacity 48 Gbp Packet Forwarding Rate 35.6Mpps RAM Data Buffer 4Mb MAC Address Table 4K PoE supply management Port 1-24 support IEEE802.3at/af PoE standard PoE through pin 1 2 4 5 +/3 6 7 8 – Input Power AC: 100-240V～50/60Hz Dimension 440*178*44mm(W x D x H) Power Consumption in full conguration: b' PoE Max Power Supply: 225W Port Features Standard: the switch functions as a common unmanaged switch and all the ports of the switch can communicate with each other. CCTV: the port cache is optimized and PoE ports 1-8 have higher priorities over the other ports. All the ports of the switch can communicate with each other. VLAN: ports 1 to 22 are isolated from each other, but can communicate with ports 23 and 24(uplink ports) respectively. Isolation: ports 1 to 12 and Ports 13 to 24 belong to two different VLAN. This mode can be used to isolate supervision network and wireless network to make them not interfere with each other. Environment Operating Temperature: 0℃~40℃ (32℉~104℉) Storage Temperature: -40℃~70℃ (-40℉~158℉) Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~90% non-condensing

Brother MFC-L8390cdw 4-in-1 A4 Colour Laser Printer, Print, Scan, Copy, Fax, Duplex, USB, LAN, WiFi Brother MFC-L8390cdw 4-in-1 A4 Colour Laser Printer, Print, Scan, Copy, Fax, Up to 31 / 33 ppm print speed, Up to 600 x 600 dpi Resolution, Duplex, Up to 250 sheets Tray, Up to 50 sheets Multi-Purpose Tray, Up to 50 sheets automatic Document feeder (ADF), Up to 150 sheets paper Output, Up to 1200 x 2400 dpi Optical Scanner Resolution, Up to 1200×600 dpi Automatic Document Feeder (ADF) resolution, USB 2.0, Gigabit LAN Port, Wireless LAN, 9.3 cm Colour LCD Touchscreen Overview: MFC-L8690CDW Colour Laser Printer Wireless Laser 4-in-1 with mobile connectivity for high-volume workgroups Up to 31 ppm Print Speed USB, Gigabit Wired Network and Wireless Automatic 2-sided Printing 50-Sheet Auto Document Feeder 9.3 cm Colour LCD Touchscreen 2 x Optional 500-sheet Lower Paper Trays Features: Brother’s MFC-L8690CDW Colour Laser Printer has been designed for the needs of businesses Brother’s MFC-L8690CDW Colour Laser Printer has been designed for the needs of businesses. Built with robust materials to withstand the most challenging office environments, our range is the perfect partner for your business. Enhanced document scanning with a Dual CIS Automatic Feeder that holds up to 50 sheets, offers you a quick and simple way to scan directly to your preferred medium. The advanced security capabilities of the MFC-L8690CDW Colour Laser Printer ensures you are always in full control of your print infrastructure. You can improve data protection by restricting printer access with network user authentication and secure function lock, which allows you to password-protect certain device functions. Brother’s MFC-L8690CDW Colour Laser Printer has been designed for the needs of businesses. Built with robust materials to withstand the most challenging office environments, our range is the perfect partner for your business. Enhanced document scanning with a Dual CIS Automatic Feeder that holds up to 50 sheets, offers you a quick and simple way to scan directly to your preferred medium. The advanced security capabilities of the MFC-L8690CDW Colour Laser Printer ensures you are always in full control of your print infrastructure. You can improve data protection by restricting printer access with network user authentication and secure function lock, which allows you to password-protect certain device functions. Duplex Print, Copy, Scan and Fax Fast print speeds of up to 31ppm mono and colour Expandable paper input of up to 1,350 sheets 50 Sheet ADF 50 Sheet multi-purpose tray 9,000-page Ultra high-yield replacement toners 9.3cm Colour touchscreen LCD Wired and wireless networking Mobile connectivity Automation Automate scanning jobs and complete a task with a touch of a button with 64 programmable shortcut buttons. Simultaneous Print b'&' Scan Remove office bottlenecks with this multi-tasking feature which allows Print b'&' Scan functions to operate simultaneously. Speed Digitise and print your documents quicker with ultra fast 31ppm print speed and 56ipm Single Pass Duplex Scan / Copy, reducing the time you spend waiting for your task to complete. Professional quality Print crisp and professional laser quality documents at 2400dpi delivered by super high-yield toners working with a pre-programmed printer driver. Scalability Reduce the hassle of changing paper by having various paper types ready to print from multiple paper trays. Workflow Integrations Utilise software integration options for print and document management requirements, tailored to your business needs. Contact our team to find out more. Integrated Security Brother mobile apps for Android b'&' iOS provide the flexibilty of printing and scanning directly from your smartphoneReady to integrate with your infrastructure with Active Directory and LDAP support to restrict access to user groups in your organisation combined with NFC authentication. IPsec support for data encryption and ensuring your organisation information remains confidential. Designed for workgroups Built-in cloud apps help your team share documents by directly digitising to OneDrive, Google Drive or Dropbox. Our user interface is designed for teams – users can personalise a tab for each team member for quick and easy access to frequently used features. Specifications: Product Code MFC-L8390CDW Kit Basic Specs Functions Print, Scan, Copy, Fax Printer Type Colour Laser Product Dimensions (Width X Depth X Height) 435 mm x 526 mm x 539 mm Weight 28.1 kg Print Speed Up to 31/33 ppm Paper Type Plain Paper, Letterhead, Coloured Paper, Thin Paper, Recycled Paper Paper Size A4, Letter, A5, A5(Long Edge), A6, Executive, Legal, Folio Maximum Paper Capacity (Optional Trays 2-5) Up to 1300 sheets What’s in The Box 6,500* Page CMYK toners 50,000** Page drum unit Power supply cord and USB cable Fax line cord Driver software for Windows Quick Set-Up Guide Print Resolution Up to 600 x 600 dpi, 2,400 dpi class (2400 x 600) quality 2-Sided (Duplex) – Printing Paper Type Plain Paper, Letterhead, Coloured Paper, Thin Paper, Recycled Paper, Glossy Paper 2-Sided (Duplex) – Paper Size A4 Paper handling Tray #1 – Paper Type A4, Letter, A5, A5(Long Edge), A6, Executive, Legal, Folio Tray #1 – Maximum Paper Capacity Up to 250 sheets Tray #2 – Paper Type Plain Paper, Letterhead, Coloured Paper, Thin Paper, Recycled Paper Tray #2 – Maximum Paper Capacity (Optional Trays) LT-340CL X2 Up to 500 sheets Multi-purpose Tray – Paper Type Plain Paper, Letterhead, Coloured Paper, Thin Paper, Thick Paper, Thicker Paper, Recycled Paper, Bond, Label, Envelope, Env. Thin, Env.Thick, Glossy Paper Multi-purpose Tray – Maximum Paper Capacity Up to 50 sheets Up to 10 envelopes Manual Feed Slot – Paper Type N/A Manual Feed Slot – Maximum Paper Capacity N/A Automatic Document Feeder (ADF) Maximum Paper Capacity Up to 50 sheets Paper Output Up to 150 sheets Copy Colour / Monochrome Yes Yes Multiple Copies Up to 999 pages Enlarge/ Reduce 25% to 400% (in increments of 1%) Resolution Prints up to 1,200 x 600dpi Scan Resolution – Interpolated Up to 19,200 x 19,200 dpi Resolution – Scanner Glass Up to 1,200 x 2,400 dpi (optical) Resolution – Automatic Document Feeder (ADF) Up to 1,200 x 600 dpi (optical) Fax Compatibility ITU-T Group – G3 Modem Speed 33,600 bps Memory Transmission Up to 500 pages (ITU-T Test Chart, Standard Resolution, JBIG) Out of Paper Reception Up to 500 pages (ITU-T Test Chart, Standard Resolution, JBIG) PC Fax – Sending Yes (Network/USB) PC Fax – Receiving Yes (Mono) Connectivity Connectivity Hi-SpeedUSB2.0, Ethernet 10Base-T/100Base-TX/1000Base-T, Wireless LAN IEEE 802.11b/g/n (Infrastructure/Ad-hoc Mode), IEEE 802.11g/n (Wi-Fi Direct) Network Wireless Network Security WEP 64/128 bit, WPA-PSK (TKIP/AES), WPA2-PSK (TKIP/AES), WPA3-SAE (AES) *Wi-Fi Direct supports WPA2-PSK (AES) only. Wireless Setup Support Utility – WPS Yes Display b'&' Memory Display Type 9.3 cm Colour LCD Touchscreen Memory Capacity 1 GB Operation Power Source 253 – 240 V AC 50/60 Hz Power Consumption – Ready Approximatley 70 W Power Consumption – Sleep Approximatley 10.0 W Power Consumption – Power Off Approximately 0.03 W Noise Level Approximately 49 dB (A) Supported Operating Systems Supported OS Server 2008 (Network only), Server 2008 R2 (Network only), 7, 8, 8.1, Server 2012 (Network only), Server 2012 R2 (Network only), 10, Server 2016 (Network only) macOS v10.10.5, v10.11.x, v10.12 (Download only)

Description D-Link 16-Port 100Mbps Network Switch The D-Link DES-1016 16-port 10/100 Network Switch offers an economical way for small offices, homes, (SOHO), and small to medium businesses (SMB) to benefit from fast speed networking. It provides sixteen 10/100 ports for easy expansion of your network and a quick way to upgrade your network to Fast Ethernet connectivity. 16-Port 10/100 Switch Eco-friendly and economical – Economical yet innovative design runs cool and quiet High-speed networking – Fast Ethernet ports allow you to connect all your devices for fast file transfers and smooth media streaming Saves energy automatically – WEEE compliance reduces energy consumption without sacrificing performance Easy expansion – Expand your network to fast Ethernet connectivity to start enjoying fast downloads, smooth streaming media, and responsive online gaming Conserves Energy The DES-1016A 16-Port 10/100 Switch helps you conserve energy automatically through several methods. It automatically powers down ports that have no link, allowing the switch to save substantial amounts of power by cutting power usage for unused ports or ports connected to computers that have been shut down. The switch also conserves energy by adjusting power usage according to different cable lengths of connected devices without affecting performance Think Green The D-Link DES-1016A 16-Port 10/100 Switch is part of D-Link’s new series of SOHO devices that make use of D-Link’s Green Technology, providing energy savings, reduced heat, and a longer product life without sacrificing performance or functionality. The switch is built to follow RoHS standards to minimize the use of hazardous materials and uses recyclable packaging that helps reduce waste, complying with the WEEE directive. Superior Performance Designed for superior performance so you can enjoy fast downloads, smooth media streaming, and responsive online gaming, the DES-1016A supports the following features to ensure the best network capability possible: Auto MDI/MDIX crossover for all ports The secure store-and-forward switching scheme Full/half-duplex for Ethernet/Fast Ethernet speeds IEEE 802.3x Flow Control Specifications: 100Base-TX Interface 16 Auto MDI/MDIX Yes Console Port No RJ-45 Management Port No Alarm Port No CompactFlash (CF) Card Slot No Secure Digital (SD) Card Slot No Switching Capacity 3.2 Gbps Max. Packet Forwarding Rate 2.38 Mpps Dimension 155.7 × 122 × 41 mm Weight 0.27 kg Operation Temperature 0 ~ 40 °C Storage Temperature -40 to 70 ˚C Operation Humidity 10% ~ 90% RH Storage Humidity 5% ~ 90% RH Maximum Power Consumption 2.69 W Power Input AC: 100V ~ 240V Packet Buffer Size 2 MB FAN Fanless b'/xc2/xa0' Why not browse our wide selection of D-Link Products HERE

D-Link 16-Port 100Mbps Network Switch The D-Link DES-1016 16-port 10/100 Network Switch offers an economical way for small offices, homes, (SOHO), and small to medium businesses (SMB) to benefit from fast speed networking. It provides sixteen 10/100 ports for easy expansion of your network and a quick way to upgrade your network to Fast Ethernet connectivity. 16-Port 10/100 Switch Eco-friendly and economical – Economical yet innovative design runs cool and quiet High-speed networking – Fast Ethernet ports allow you to connect all your devices for fast file transfers and smooth media streaming Saves energy automatically – WEEE compliance reduces energy consumption without sacrificing performance Easy expansion – Expand your network to fast Ethernet connectivity to start enjoying fast downloads, smooth streaming media, and responsive online gaming Conserves Energy The DES-1016A 16-Port 10/100 Switch helps you conserve energy automatically through several methods. It automatically powers down ports that have no link, allowing the switch to save substantial amounts of power by cutting power usage for unused ports or ports connected to computers that have been shut down. The switch also conserves energy by adjusting power usage according to different cable lengths of connected devices without affecting performance Think Green The D-Link DES-1016A 16-Port 10/100 Switch is part of D-Link’s new series of SOHO devices that make use of D-Link’s Green Technology, providing energy savings, reduced heat, and a longer product life without sacrificing performance or functionality. The switch is built to follow RoHS standards to minimize the use of hazardous materials and uses recyclable packaging that helps reduce waste, complying with the WEEE directive. Superior Performance Designed for superior performance so you can enjoy fast downloads, smooth media streaming, and responsive online gaming, the DES-1016A supports the following features to ensure the best network capability possible: Auto MDI/MDIX crossover for all ports The secure store-and-forward switching scheme Full/half-duplex for Ethernet/Fast Ethernet speeds IEEE 802.3x Flow Control Specifications: 100Base-TX Interface 16 Auto MDI/MDIX Yes Console Port No RJ-45 Management Port No Alarm Port No CompactFlash (CF) Card Slot No Secure Digital (SD) Card Slot No Switching Capacity 3.2 Gbps Max. Packet Forwarding Rate 2.38 Mpps Dimension 155.7 × 122 × 41 mm Weight 0.27 kg Operation Temperature 0 ~ 40 °C Storage Temperature -40 to 70 ˚C Operation Humidity 10% ~ 90% RH Storage Humidity 5% ~ 90% RH Maximum Power Consumption 2.69 W Power Input AC: 100V ~ 240V Packet Buffer Size 2 MB FAN Fanless b'/xc2/xa0' Why not browse our wide selection of D-Link Products HERE